Shetland 535 refurb step by step

Thoughts, Ideas and General Questions
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

After cutting the panels to size, tapered on one side to match the cockpit shape, it became apparent that the 2000mm x 830mm panels of 18mm ply would be very difficult for a one-armed man to lift into the cockpit and manoeuvre into position. I therefore decided, after some thought, to cut the panels at the position of the middle cockpit floor bearer, so the deck will now consist of four panels instead of two.

After a few adjustments, I trial fitted the two on the starboard side but the port side will have to wait until my next visit. In the meantime I can finish off the first two and treat them at home.

I intend to coat the whole of each panel with wood preserver then to paint the bottom surface and sides/edges with some high-quality exterior gloss paint (Sadolin Woodshield or similar). The top surface of each panel will have a central area of blue non-skid paint (hopefully a similar colour to the superstructure) and this will be bordered with a couple of inches of Rustins yacht varnish. This should be practical and attractive and should ensure the wood is well-protected.
You do not have the required permissions to view the files attached to this post.
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

Afrer a very pleasant weekend (shock!) further progress has been made on Meggy's deck. The plywood deck bearers/spacers and the underside of the deck panels have been treated with wood preserver, followed by exterior wood stain and a final coat of Berger exterior gloss. If that doesn't protect them I don't know what will.
Meggy 089 under-deck painting ongoing.jpg
The top surface has had one coat of Ronseal Yacht Varnish. It will eventually have further coats and some areas of non slip paint but I'm leaving that until they are in situ and I can see where the other deck fittings go.
Meggy 088 Port deck panels trial fit.jpg
Meggy 087 Deck bearers in place.jpg
Seen here bedded in place on black Sikaflex and awaiting their stanless steel fixing screws.
You do not have the required permissions to view the files attached to this post.
Last edited by Whammers on Mon Apr 25, 2016 2:10 pm, edited 1 time in total.
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

The under-deck areas will have some expanding foam and some plastic bottles to add bouyancy but initial experiments have shown that a can of expanding foam doesn't go very far at all. I will need a couple more cans to supplement my empty plastic water bottles. :roll:
User avatar
Freebird19
Posts: 79
Joined: Tue Jan 12, 2016 5:57 pm
Location: Black Hawk "Freebird" Norfolk

Re: Shetland 535 refurb step by step

Post by Freebird19 »

Just wanted to say thank you for your ongoing post. I enjoy reading of your progress and it's nice to have good clear photos to see what you are up to! Looking forward to seeing the finished article, should be very impressive!
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

Thanks. :)

I've made good progress with the deck over this warm sunny weekend and have also put a coat of paint on the hull. Detailed post to follow, hopefully tomorrow.
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

The weekend just gone was a glorious opportunity to a) make progress with the deck, and b) get some paint on the hull. Over two days of glorious weather I managed to achieve both.

I added four areas of expanding foam to the under-deck area (I don't know what the right term is - we'll call them 'splurges'). I 'cast into' them some plastic tubes so that water can drain from the outer areas into the central bilge and added some 'enhanced buoyancy reservoirs' (aka empty plastic bottles), held in place with some mini-splurges of foam, which expands and dries nice and firm.
Meggy 090 Under deck buoyancy.jpg
The deck panels, newly fettled after recent trial fit were laid in place to limit the expansion of the foam and the forward two were fastened down with two stainless steel screws each (there will be four each eventually) into the under deck bearers.

The rear panels I've left loose for the moment as I still need to finalise bilge pump installation and the rear seat. Once the deck and seat are finalised I will mask up and add the non-slip areas. Shame really, because I quite like the varnished look.
Meggy 091 first deck installation further alignment needed.jpg
Meggy 093 Cockpit looking better.jpg
You do not have the required permissions to view the files attached to this post.
Last edited by Whammers on Tue May 10, 2016 9:49 am, edited 1 time in total.
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

Late on Saturday afternoon, I turned my attention to painting the hull. As mentioned in a previous post, I am experimenting with a metallic silver (Rustoleum Combi-color, 'white aluminium') applied with a roller. Conventional thinking says metallic finishes need to be sprayed and I'm sure they do for best effect but I'd previously tried rolling it onto the transom and the cabin bulkhead, with passable results. Now it was time to do the hull.

The key to a good finish with the Rustoleum is getting the paint consistency just right for the ambient temperature. I got this wrong with the blue on the superstructure and may yet repaint it before putting the fittings back on.  The paint needs thinning with white spirit by about 10-15% but there's quite a lot of guesswork involved!

The metallic paint also needs mixing continually to try to keep the metallic particles in suspension and it's not entirely successful, leaving a slightly patchy finish. The need to move slowly with the first coat, to achieve coverage, didn't help. A second coat, moving more quickly, and possibly with an assistant to lightly 'tip' with a brush after the initial roll-by (Google 'rolling and tipping') may well achieve something better.

Anyway, I got the sides done on Saturday and returned on Sunday to do the underside.
Meggy 092 First paint on hull.jpg
Of course, there are areas I cannot reach with the boat on the trailer, and these will have to be patch painted once the main areas have fully hardened (at least three weeks) and I can roll the boat back on the trailer by a foot or so.

I got most of the hull done, though the shape, and working on my back for part of the job was quite strenuous on the arm. There is just a small area to complete under the rear of the hull - I had to abort due to the paint in the tray becoming a bit 'manky' as it kept skinning in the hot Lancashire sun. 8-)

Close up, it's irritatingly patchy but, from a distance I like the look; the grey hull with the blue superstructure and the black windows give the boat a kind of mean and moody air... as if Meggy has gone a bit goth..
Meggy 094 Hull painted first coat.jpg
You do not have the required permissions to view the files attached to this post.
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

After some time thinking about the attempted silver metallic finish on the hull I returned to the boat and reappraised. I was not happy.  The finish is way too patchy to be acceptable - it's really not possible to keep the metallic particles evenly distributed when applying by roller. So, the silver hull will now be painted over.
Meggy 101 Patchy silver finish.jpg
I wanted to go for all blue, cos it's a great blue, but my better half said she 'liked a bit of contrast'. We have settled on a fairly radical scheme now; the lower part of the hull will be ultramarine blue, like the topsides but the tapered area between the rub rail and the spray rail (I think it's called the "sheer strake") will now be bright orange! As everyone knows, orange and blue go well together so she should look mega when it's done!
You do not have the required permissions to view the files attached to this post.
Last edited by Whammers on Mon Jun 06, 2016 10:14 am, edited 1 time in total.
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

Next step was to repaint the transom ready for a new transom pad. The sub-standard silver was flatted down and overpainted with ultramarine blue...
Meggy 098 Transom repainted.jpg
Then I set to making a new transom pad. The old one was thin and bendy (old 12mm ply) so I used more robust 18mm ply for the new one. I used the old pad as a template for marking and drilling the holes but took the opportunity to make the pad slightly larger to spread the load better. Once cut and drilled my "rack o th'eye" said that it didn't look right... investigation showed the motor had actually been mounted slightly left of centre. After pondering on this for  few minutes I decided it was too far left to have been done by mistake so it must have been done deliberately, possibly to make a little more space for an auxiliary engine. Whatever, the reason, I decided to go with it as the boat had clearly been working fine in that configuration prior to being taken out of the water. So if the transom plate looks a little odd, that's why.
Meggy 099 old and new transom pads.jpg
You do not have the required permissions to view the files attached to this post.
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

Before treating the pad I took it up to Meggy for a trial fit and found that the holes all lined up fine but that my increased "footprint" blanked off the outer splash well drain holes! On the picture below you can see my markings on the bits that needed trimming off..
Meggy 100 Transom pad trial fit.jpg
Once happy with the fit I took the pad home for a severe protective treatment regime - first I slathered it (technical term) in wood preserver, followed by a heavy coat of exterior woodstain on the inside face and the edges, then four coats of yacht varnish on the outer face, also covering the edges. The sunny weather was great in that it dried the varnish quickly enough to get two coats on each day over the weekend.
Meggy 102 varnihed transom pad.jpg
You do not have the required permissions to view the files attached to this post.