jersey shetland help wanted

Thoughts, Ideas and General Questions
jerseysheltie
Posts: 1
Joined: Fri Jun 03, 2011 7:00 pm
Location: tally, shetland sheltie and the boat is in jersey

jersey shetland help wanted

Post by jerseysheltie »

hi every one im new to the site so please for give me if im being a bit slow lol.

i have owned my sheltie now for 4 years and has mainly be used for diving on wrecks so as you can imagn
shes looking a bit tired ,
also affter taking her out in some "slight swell" and geting some good air lol the deck gave way .
i always knowen that the deck needed relacing just not so soon so rely im wondering has any one
else replaced there deck and how much of a pain in the a..e it was .
would love to see peoples shelties as i would like to see what otheres have done as when i do my deck im
having a totale stip out and revamp but sadly carnt see any phots on the site .
Kilrymont
Posts: 1
Joined: Sat Aug 06, 2011 10:44 pm

Re: jersey shetland help wanted

Post by Kilrymont »

Hi, my first post on this forum.

Surprised to see no replies to your query, so here goes...

We have a Sheltie that also dates from, we think, the mid 80s. We were aware of our deck doing things that decks shouldn't do and also that the void below was waterlogged.

So eventually we bit the bullet and got her under cover for the inevitable stripout work. It takes a big chunk of courage to take a saw to your beloved boat but once we made a start it became less dreadful especially once we could see just how low the standard of original construction actually was. There were no stringers to support the deck board which was made of 9mm ply - which had begun to delaminate in places. The original foam injected below had broken away from both hull and deck underside and as a result of that we were able to feel the deck "working" under our feet when the boat was at any kind of speed in a chop or a swell. The plastic corks inserted where the foam was injected were a lousy fit and water could be seen squelching around underneath as it took someone's weight close by.

The Shetland deck depended heavily on this foam for support. It was only supported where it touched down on the hull at its edges - and once the boarding was exposed and lifted we could see exactly how crap was the original profiling of its outer edges. It was like an apprentice's first day effort ended up getting used anyway.

The clean up of all the nooks and crannies under the splash well was a bit of job - neither of us are small - but it was all done eventually and we commenced the deck rebuild. The worst bit was dealing with the sump under the splashwell. We used marine grade ply of 12mm laid on top of redwood stringers profiled exactly to the hull contours at approx 18" centres. These were resined to the hull using advice from a pro boat builder in Dundee - Simpson Marine - who also sold us the matting and polyester resin we used. He advised strongly against the use of Epoxy resin for this job. We made our own resin adhesive paste by mixing resin with talc could you believe? Again, on Simpson advice. We did find that if the air temp was too low the resin took a greatly extended time to set so were able to use space heaters to offset this - this work was done through a winter in a huge disused factory in Dundee. The Sheltie was balanced on her keel line on matting and closely spaced wooden wedges used along the chines to keep her completely levelled and supported evenly throughout.

We laid the deck in two sections but did not disturb the deck inside the cabin - we found no reason to lift it there as investigation showed it to be dry underneath and in good order, nothing like the disaster under the outside main deck.

The new deck ply was stainless-screwed to the stringers, and resin pasted all around and this given a smooth finish all over.

Right now I can't remember if we refoamed the voids between the stringers before the GRP was applied or not - but I feel it was before! It's several years now and my command of detail isn't improving with the years' passage. We debated long over whether it was better-to-foam or not-to - but we decided that with the kind of hammering the hull skin takes when slamming over a chop that it needs all the support it can get, so elected to use closed cell foam to replace the original - but to take a deal more care than Shetland had done when the hull was manufactured. And so it went - each space between pairs of stringers was foam injected to keep things as strong as possible. I think we cut out circular cores from the new deck for foam injection and resined the cores back in place once the foam had set, to preserve the sealed integrity of the under deck void and maximise the chance of keeping water out over the succeeding years.

Then two thicknesses of CS matting laid over the whole decking up the hull sides for a short distance, and were thoroughly roller-resined down. Simpson also made up some special gelcoat to finish off the deck topside colour matched to the sheltie's cream topside to keep things looking trim.

It wasn't a cheap job but we decided that since it had to be done we would do it properly - and so far the result has repaid our efforts well. The deck is as rigid underfoot as any other I've ever been on.

On another topic....
I've seen some debate over what size of motor is acceptable on a Sheltie. Shetland made the same hull do for both the Sheltie and the 535, yet state the Sheltie's max HP rating is, I think? 40hp. Which seems a little modest to me, but when the 535 has a higher max rating it seems to make a nonsense of the factory figures.

Ours has the original Mariner 55 supplied by the original Shetland dealer who we assume felt it safe to exceed the factory figure. Our experience of using this motor is that it's a pretty close to perfect match overall. Being a two stroke twin, it's possibly one of the lighter 55 rated units around? It's the same motor as the Yamaha 55 twin cylinder of the time, but with Mariner badges.

As to performance, we find ourselves seldom able to use the full output of even this rather elderly engine. With the way we're set up we get on the plane around 13-14 knots and have a top end in flat conditions of mid twenties at best. But we usually throttle back to an even 20 knot cruise and get excellent consumption figures that way. But in the real world the sea is seldom calm enough for high speeds to be maintained in terms of personal comfort and indeed hull longevity - subjecting a 25+ year old GRP hull to such brutal hammering as results from over 20knots in a lumpy sea isn't very sensible.

For safety we also keep an old 15hp Mariner bolted on as our aux motor. With this we can easily do 6-7 knots into a stiff breeze and we know we can get home on this motor. We regularly see bigger boats than ours with wee 3/4/5hp units on a bracket, which would struggle to give steerage at all, never mind out on the sea if conditions shifted for the worse. Inevitably this means we're more tail-heavy than many a similar craft, but we offset that as far as we can by keeping all other hefty kit stowed up front. Seems to work quite well overall.

Apologies for the extra bits'n pieces added on here, admins can always trim if any is felt inappropriate to the OP's enquiry.

That's it - happy to answer any queries from any of the above if it'll help other members.
Safe boating
K