Family 4 MK3 - do I need need a bung?

Thoughts, Ideas and General Questions
Adam
Posts: 86
Joined: Tue Oct 02, 2018 3:38 pm

Family 4 MK3 - do I need need a bung?

Post by Adam »

Hi there,
New to Shetlands and big boats hence my silly question here.
I've just purchased F4 and do I need to put draining bung in the hole at the bottom of the transom before using the boat?
I used to use small 14ft fishing boat and it was obvious to close the draining whole. Do I need to do it in my F4 as well?
Cheers!
Last edited by Adam on Wed Oct 17, 2018 8:10 am, edited 1 time in total.
Shetland Family Four "Foxy Lady" , 70 hp Johnson EFI four str. You can meet me in the Poole Bay or Lyme Bay area from time to time \m/
daveflack
Posts: 291
Joined: Fri Nov 08, 2013 6:54 pm
Location: Black Hawk "Atlast"Ullswater, now a 4+2

Re: Do I need a bung?

Post by daveflack »

Hi, the obvious answer would be yes,but have a good look & find out were the hole goes,is it straight thro overboard,or, does it go into the support box were the out board is fitted on the outside of the transom? Whichever I'm only suggesting caution. Maybe an F4 owner will enlighten us.
DACS
Posts: 77
Joined: Sat Jul 19, 2014 9:59 am

Re: Do I need a bung?

Post by DACS »

As daveflack has said, it depends where the hole connects to.

if it is at the very bottom of the transom then it probably goes straight into the hull and is intended to drain water out of the boat when it is ashore or on a trailer. This needs a bung when you launch the boat as it will normally be below the waterline and will allow water in to flood the hull.

If the hole leads into the outboard well, where the engine fits, then it is intended to allow water out of the space around the engine and should not have a bung. Outboard boats often have two such drain holes in the corners of the well. The transom of outboard boats has to be cut low enough to ensure that the engine is deep enough in the water. However, the outboard well ensures that the boat is still watertight to the level of the top of the hull. The drain holes simply allow any water that finds its way into the well to escape again.
Adam
Posts: 86
Joined: Tue Oct 02, 2018 3:38 pm

Re: Family 4 MK3 - do I need need a bung?

Post by Adam »

Thank you for the answers guys. The hole is at veeery bottom of the transom and I need to check where it goes. But 100% sure that it doesn't go to the outboard well. I should have ask the owner but he has had an accident and it is not possible to talk with him and rest of the family have no idea about the bung.
Shetland Family Four "Foxy Lady" , 70 hp Johnson EFI four str. You can meet me in the Poole Bay or Lyme Bay area from time to time \m/
Adam
Posts: 86
Joined: Tue Oct 02, 2018 3:38 pm

Re: Family 4 MK3 - do I need need a bung?

Post by Adam »

I did check everything yesterday and I definitely need to put a bung there. The hole goes to bilge well so - bung definitely.
Shetland Family Four "Foxy Lady" , 70 hp Johnson EFI four str. You can meet me in the Poole Bay or Lyme Bay area from time to time \m/
Franknstein
Posts: 35
Joined: Tue Jan 19, 2016 8:24 am

Re: Family 4 MK3 - do I need need a bung?

Post by Franknstein »

There are two drain holes on the rear transom of the F4.

The top one is an open drain (no bung) which sits at the lowest point of the outboard splashwell.
The lower one has a bung (brass screw-in type on mine) which sits right at the lowest point of the bilge - this allows you to drain the bilge area when boat is put on the hard.

I would be surprised if there wasn't a bilge drain on your boat - I've never seen a boat without one!.
Adam
Posts: 86
Joined: Tue Oct 02, 2018 3:38 pm

Re: Family 4 MK3 - do I need need a bung?

Post by Adam »

Thank you! You are absolutely right mate!
Shetland Family Four "Foxy Lady" , 70 hp Johnson EFI four str. You can meet me in the Poole Bay or Lyme Bay area from time to time \m/