Broken lower leg

Thoughts, Ideas and General Questions
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Broken lower leg

Post by Clive »

Feel a bit embarrassed to have only just noticed this...
First launch when we got the boat, I didn’t secure the boat on the trailer and being a roller coaster the boat slipped off in shallow slipway water. Later I found a scuff on the keel but didn’t see the engine must have bottomed out too. Pic shows the fin under the prop has snapped off. Apart from less steering (I bought a fin thing cos the boat wanders, know why now 😕) do I need to worry? I could keep an eye out for a used replacement...
No other damage fortunately.
You do not have the required permissions to view the files attached to this post.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Broken lower leg

Post by dellquay13 »

Ooops! Leg up next time you launch then Clive...

The lower skeg gives a lot of protection for the prop. You could look at fitting something like a PropGuard or similar. They are primarily to stop the prop chopping up Dolphins or swimmers, but they also do a good job protecting the prop against rocks and crab pot lines.

In the long term, your options are find a good 2nd gearcase complete (don't get into swapping your gears into another gearcase unless you have very deep pockets), or looking for an Aluminium engineering company who could weld a replacement skeg on. Steel Developments ltd weld Aluminium prop repairs, they may be able to do the casing too. Poking your nose around the door of the workshop at local boatyards might get you information about local repairs.

I would wait until the winter before doing anything more than fitting some kind of propguard, and enjoy the coming season, but with care in shallows.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Broken lower leg

Post by Clive »

Agree with all of that - I missed the risk to the prop so thanks. I’m all river at the moment and with a 35hp engine can’t see me doing much coastal work. That said I just removed the thermostat and it was jammed with bits of shell!
The mishap was on the slip at Stoke Lock on the River Wey, which is a private public slipway - pay a one-off fee to use and get a key to the gate. It’s quiet so it’s highly likely to be on the bottom 18 months later. Think I’ll go down with a rake and do some dredging! If I can get the skeg back it will help.
Thanks for the advice.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Broken lower leg

Post by Clive »

dellquay13 wrote: Wed Apr 28, 2021 7:38 am
You could look at fitting something like a PropGuard or similar.

Steel Developments ltd weld Aluminium prop repairs, they may be able to do the casing too.
Just bought a PropGuard - in for a penny as they say, but as I'm mainly trolling and in quite grubby water it's worthwhile for the improved control, weed and fishing line protection and apparently, improved fuel economy.

And thanks for the Steel Developments contact. Just spoke to them and they repair lots of skegs! If I retrieve the skeg they will weld it back, if I can't they will make one up and the cost is around the £100+ mark, takes 5 days or so. Bit cheaper than the replacement I saw for £700. Should feel like a new boat with new steering cable too.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
vreagh
Posts: 327
Joined: Sat Aug 02, 2014 5:46 pm
Location: Cornwall

Re: Broken lower leg

Post by vreagh »

Nice to hear Steel Developments are still going. I sent a 40hp Perkins outboard prop there 50yrs ago. Most of a blade had gone. Got it back like new, couldn't see the weld and all sprayed up. Proper job.
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Broken lower leg

Post by dellquay13 »

Steel developments sorted a prop i dinged in rocky shallows on Loch Lomond about 25 years ago and it was like new. They fitted a new torsion bush to another prop that started slipping on a long passage along the N Brittany coast where I had to do 80miles and couldn't get above 2000rpm without prop slip, a gruelling 12hr slog over a full tide back to the port where I had launched at the start of the holiday.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Broken lower leg

Post by Clive »

Leg's in with Steel Developments. I managed to crack one of the fins due to not realising there was another bolt under the trim tab so that's added to the bill. Quite nostalgic, I bought my first house in the next road in 1974.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Broken lower leg

Post by Clive »

Got the foot back today, really good job. Got primer and paint coming. Anyone know about the rubber tube? The connector has no hole so I can only think it’s the Speedo option that isn’t installed. There’s a knots and speed dial as an accessory fitted thru the hull so assume I don’t need to worry about it on the engine. Worked that out after I’d cleaned out the water intake for it!!
You do not have the required permissions to view the files attached to this post.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Broken lower leg

Post by dellquay13 »

Looking good.
I'd be tempted to change the gearbox oil now, I'd be paranoid about it having gotten too hot during the welding.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Broken lower leg

Post by Clive »

It was drained before I took it in so yes, it’ll have nice new oil!
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.