Fishfinder

Thoughts, Ideas and General Questions
daveflack
Posts: 291
Joined: Fri Nov 08, 2013 6:54 pm
Location: Black Hawk "Atlast"Ullswater, now a 4+2

Fishfinder

Post by daveflack »

hi all trust everybody is keeping safe & well, anyway, is there anybody out there with a 4+2 that's fitted with a working fishfinder/depth gauge ? I've fitted a lowrance unit to mine & it refuses to work at speeds above 3mph. I contacted lowrance about this issue & they basically said it's because the transducer is mounted on the wrong side of the transom & therefore picking up interference from the prop rotation, so I moved the trans to the other side & low & behold after all the work moving & re-threading the wiring ------ it still doesn't work, !!!!!! if you have a working unit on your boat what is the make & where is your trans fitted ? cheers Magic
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Fishfinder

Post by dellquay13 »

The thing is making sure the skimmer is sitting in clear water, not full of bubbles or turbulence. I have always fitted mine (5 boats with various lowrance over the years) behind clean and smooth sections of hull, at least 4" away from any lateral chines, and with the edge of the skimmer bracket 1-2mm back from the transom edge so it causes no turbulence, but keeps the skimmer as far as possible out into clear water.

I have always mounted my skimmers about 30-40cm away from the keel line, on either port or starboard sides.

More recent Lowrance units with added features such as hdi or chirp also have switchable frequency bands, and can be used with a variety of skimmers. I had a lot of headscratching with an elite X5 that was supplied with a 4 band skimmer, but the head unit was programmed for a different 4 band frequency set. Once I had found where to switch the lowest frequency in the menu, it was as good as gold.

Having said all that, I've never seen a fish finder that will show a consistently good picture at planing speeds, once I get above 16mph I ignore the image and just use the depth readout.

If I'm going too fast for the sounder to keep up and I'm worried about what is below me, I'm going too fast for the water conditions and depth.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Fishfinder

Post by dellquay13 »

Other things to consider are the state of any antifouling in front of the skimmer, if it is too pitted and uneven it can cause turbulence as can any substantial fouling. I have always antifouled my skimmers as well, but not too thickly.
Keep transducer cable routing away from engine power and control wires. You can rule out the engine control wiring being at fault though by switching the engine off, if the sounder suddenly clears up then the engine is causing electromagnetic interference.

If all else fails, you can epoxy the skimmer to the inside of the hull, or epoxy a container in and sit the skimmer in oil, as a through hull system. If you go this route, bubbles in the epoxy or in the grp hull itself can cause interference. The in oil method is used on lots of yachts and if your chosen oil container is big enough, you can move the transducer around by a few centimetres to avoid any bubbles in the grp.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
daveflack
Posts: 291
Joined: Fri Nov 08, 2013 6:54 pm
Location: Black Hawk "Atlast"Ullswater, now a 4+2

Re: Fishfinder

Post by daveflack »

Hi, thanks for your replies, I am suspecting it's a turbulance issue but not sure how to get around it. My 1st fitment was done based on ease of install & length of cable I opted for a route thro' the port side locker so as to come out at the dashboard, obviously this was running alongside all the main electric feeds, 1st mistake, I didn't realise how critical it was to avoid power leads. During the close season whilst the boat was on it's trailer I re-routed the cable thro' the stbd locker, no wires just a fuel tank, I also moved the trans from port to stbd side on transom. I've tried turning the motor off & just coasting but it makes no appreciable difference. The trans is mounted on the transom under the swimming platform almost under the vertical bolt line of the engine mounting box & I also bonded on a sternsaver to avoid drilling holes in the transom. I suspect from Dellquay's fitting guidelines I'm to close to the step change of the hull bottom surface, (is that what you refer to as a lateral chine ? ) thanks again, more food for thought. Re 1 - 2 mm on the bracket, if I was mounting directly to the transom I would secure the bracket in such a way that the bottom of the bracket was marginally above the radius of the hull moulded edge.
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Fishfinder

Post by dellquay13 »

Hi Dave,
The chines are the ridges where different planes of hull meet, and cause a disturbed flow, upsetting transducers. They are more likely to be causing your problem than the cable routing as the cable is screened against most electromagnetic interference.
Having the bracket just up to the edge of the transom radius sounds about right.
Chris
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...