Saker cabin roof

Thoughts, Ideas and General Questions
ianslim
Posts: 13
Joined: Fri Sep 17, 2021 11:12 am

Saker cabin roof

Post by ianslim »

Hi All, having removed the head lining in the cabin, I have now revealed, A hole about 100mm in dia that has been plugged with a "plastic lid", for want of a better description. Whatever was there before was obviously screwed in place with a doz or so screws. The question is what was it?? Any ideas?? :?: :?: Many thanks, Ian
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Saker cabin roof

Post by dellquay13 »

A roof vent. I removed my old one and fitted a solar powered fan vent. Very effective at keeping condensation at bay when sleeping aboard, but the rechargeable battery needed replacing after about 12 years...
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
ianslim
Posts: 13
Joined: Fri Sep 17, 2021 11:12 am

Re: Saker cabin roof

Post by ianslim »

Thanks again Dellquay13.
ianslim
Posts: 13
Joined: Fri Sep 17, 2021 11:12 am

Re: Saker cabin roof

Post by ianslim »

Got the fan , now just need to fit. The foam under the floor appears to be the sourse of the condensation it's wet. Short of ripping the floor up what's the best way to dry it out. I was thinking about drilling a hole at the stern/transom area but I think there are "stringers" preventing any "flow" to the rear???
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Saker cabin roof

Post by dellquay13 »

If the foam is wet, it's likely the floor ply will be soggy underneath and starting to delaminate, it's not as difficult to replace as you first imagine, and it helps dry the foam while the floor is up. Get plenty of epoxy painted to the underside of the replacement ply to get it to last better. Originally the boat would have had 1/2" ply, but most people replace with 18mm. (I was worried about weight so stuck with 12mm, as there was plenty of support from the foam underneath)
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
ianslim
Posts: 13
Joined: Fri Sep 17, 2021 11:12 am

Re: Saker cabin roof

Post by ianslim »

I'm thinking the floor has to come up, replace the foam with poly beads or is the foam needed for rigidity? The question is why is the foam wet in the first place? Nothing obvious at this stage.
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Saker cabin roof

Post by dellquay13 »

Leaky or cracked windows, leaky hull to top moulding joint under the rubbing steaks, there were lots of places where the rain found it's way into my boat that's 30+ years old.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Saker cabin roof

Post by dellquay13 »

The fore and aft rigidity will come from the keel line, I think the foam will give the hull lateral rigidity by preventing any compression from twisting forces.
It certainly helps support the floor, and I believe it will help reduce flexing in and out of the larger flatter areas of the hull. These do still flex to some extent, possibly on purpose. I can tell from tiny cracks appearing in the antifouling at the end of the season in certain places where bulkheads and cabin fittings are bonded to the hull and increase hull rigidity, that unbonded areas are flexing a bit in heavier seas.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Saker cabin roof

Post by Clive »

dellquay13 wrote: Tue Nov 23, 2021 12:30 am but the rechargeable battery needed replacing after about 12 years...
Can’t complain at that!
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.