Mooring to a ring?

Thoughts, Ideas and General Questions
g4fne
Posts: 17
Joined: Sun Dec 12, 2021 7:59 pm

Mooring to a ring?

Post by g4fne »

Hi folks ... Im sorry for what is probably a really basic question (newbie alert lol) but I cant seem to find an answer online.

The boat came with mooring lines that have a spliced loop one end. I understand this loop stays attached to the cleats on the boat (this seems simple enough ... thru the eye of the cleat and then over the horns? ) ..... but where I am mooring to have rings. Others boats at the mooring seem to be attached by going thru the loop and then back to the cleat on the boat (ie no knot at the ring). This keeps the line very short (tidal but floating pontoon so makes sense) .... but can i just check that i should tie the knot over the spliced loop at the cleat? ..... I hope this makes sense :roll: :roll:
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Mooring to a ring?

Post by Clive »

Up to you! But if everyone ties on to the cleat I would do the same. The reason I do is to make it more difficult for anyone to untie you at night - you’ll feel the boat move if anyone tries. Someone might have a better reason!
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
g4fne
Posts: 17
Joined: Sun Dec 12, 2021 7:59 pm

Re: Mooring to a ring?

Post by g4fne »

Clive wrote: Thu Jan 20, 2022 8:06 pm Up to you! But if everyone ties on to the cleat I would do the same. The reason I do is to make it more difficult for anyone to untie you at night - you’ll feel the boat move if anyone tries. Someone might have a better reason!
Ah right, thanks Clive, yes that makes sense ... Is there a particular knot that is good to use when i go back to the cleat ... there seems quite a few options?
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Mooring to a ring?

Post by Clive »

Pro spec?!😉
Cleat hitch. So easy when you get the hang of it.

Quick
https://youtu.be/Wl5LnLUs-Zs

Or very detailed
https://youtu.be/KaF9lFn0Inw

I watched both and liked them, so many knots on YouTube.

Good luck
Clive
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Mooring to a ring?

Post by dellquay13 »

Loop over your cleat, two turns through the ring then back to your cleat with an Oxo knot (round the cleat, criss cross over the top then another turn around the cleat).
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
g4fne
Posts: 17
Joined: Sun Dec 12, 2021 7:59 pm

Re: Mooring to a ring?

Post by g4fne »

dellquay13 wrote: Fri Jan 21, 2022 11:19 pm Loop over your cleat, two turns through the ring then back to your cleat with an Oxo knot (round the cleat, criss cross over the top then another turn around the cleat).
thankyou :)
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Mooring to a ring?

Post by dellquay13 »

Rings can be awkward to moor to long term without causing wear or chafe on your lines. If you simply loop through the ring once or twice then you need to keep an eye out for wear and tear. If you use any tight locking knot on the ring to avoid chafe it becomes awkward to get on and off the berth without leaving the line on the ring for your return, and then you have to keep your line out of the water while you are gone and hope it's there when you get back.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...