Foldable seat legs

Missing a vital part? Need to track down a spare? Just ask.
Paulf
Posts: 23
Joined: Mon Mar 16, 2020 12:17 pm

Foldable seat legs

Post by Paulf »

Does anybody have or know of somewhere that sells 2 foldable legs for a bench seat for a 570?
I've attached a picture of one that I currently have but require 2 more to aid my refurbishment project. They ideally would be 3/4" inch diameter and approx 12 inches in length.
Any help would be greatly appreciated.
You do not have the required permissions to view the files attached to this post.
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Foldable seat legs

Post by Clive »

I have what looks like the same on the rear cockpit seat on my 4+2. I’m planning to make it a permanent seat but not decided when yet as I have more urgent things to do. If you don’t find any keep in touch and I’ll let you know if/when they’re available.
Clive
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
Paulf
Posts: 23
Joined: Mon Mar 16, 2020 12:17 pm

Re: Foldable seat legs

Post by Paulf »

Hello Clive,
Thanks for the post and the offer of your legs. May I hasten your work schedule and offer you in exchange my fixed ones which I hope to replace with the afore mentioned foldables. They are purpose made from 2.5" stainless and the plastic fittings will match the colour of your Shetland if it's beige.
Thanks again and keep in touch,
Paul
You do not have the required permissions to view the files attached to this post.
daveflack
Posts: 291
Joined: Fri Nov 08, 2013 6:54 pm
Location: Black Hawk "Atlast"Ullswater, now a 4+2

Re: Foldable seat legs

Post by daveflack »

Hi guys, interesting topic this, if I remember rightly one of members was asking for the dimensions of both the leg & hinge assemblies some time ago, I was unable to get pictures of said bits but tried my best to produce a drawing. It might be worthwhile taking some more photos from different sides & putting some dimensions on the relevant bits.Cheers magic
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Foldable seat legs

Post by Clive »

These look interesting, esp as I’m gradually replacing crumbling plastic with stainless (not the cheap option!). Is this the bench at the stern?

I’ve also almost finished fitting sliding drawers under the diner bench seats and scrapped the fold out end that made the double bed so I also have all that.

Mine is 1988 and cream with grey interior panels. Reupholstered cushions are blue. Fashion has gone full circle and it looks quite modern!
Where are you based? I’m in Guildford. I’ll get some pictures of my seat and supports.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Foldable seat legs

Post by Clive »

daveflack wrote: Tue May 17, 2022 7:30 pm It might be worthwhile taking some more photos from different sides & putting some dimensions on the relevant bits.Cheers magic
Hi Dave - I’ll do that for the record, but looks like I won’t have the parts for long!
I’m wondering how to fabricate a front panel for the rear bench. I’d like a GRP finish so it matches the side benches but not done anything like that, just repaired holes and spider cracks!
Cheers,Clive
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Foldable seat legs

Post by Clive »

Oops, forgot measurements but this is what I have. The hinge mechanism isn’t the best as it won’t keep the seat up so the front edge is on the floor (see picture) so I usually keep it up, hence the idea to make it permanent.
You do not have the required permissions to view the files attached to this post.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
daveflack
Posts: 291
Joined: Fri Nov 08, 2013 6:54 pm
Location: Black Hawk "Atlast"Ullswater, now a 4+2

Re: Foldable seat legs

Post by daveflack »

Back again, the hinges are only to act as a rear support, the design is quite clever as it allows the seat to be stowed vertically against the Hull sides when not required, simples, a handy idea if you do a bit of fishing & need a bit of open space in the cockpit. Cheers magic
Paulf
Posts: 23
Joined: Mon Mar 16, 2020 12:17 pm

Re: Foldable seat legs

Post by Paulf »

Hi Clive,
I'm so glad I asked as this small request has seemed to spark interest and nostalgia in equal measures.
Yes the seat is in the stern and as correctly identified both seats (a single seat port and a double seat starboard) could potentially fold back in line with the hull. The single seat had rotten chromed fixed legs on her when purchased and I replaced with the stainless ones.
What I referred to as plastic isn't exactly, it's a composite called tecapeek. I'm a CNC machinist by trade and this material was hanging around after finishing a job for Lotus F1. The problem with the fixed legs I later discovered was that the larger diameter hinders both of my petrol tanks to be placed side by side, and reinstalling the original legs would be a better option.
I am based in Lymington, Hampshire, the boat's currently on the drive and it looks like I've bitten of more than I can chew workwise.
Paul
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Foldable seat legs

Post by Clive »

Haha, welcome to the world of older boats! I seem to have as many jobs now as when I bought mine in 2019. I think as you improve things you find other bits to do.

Does yours have a swim deck and flat stern or (don’t know the term) an inset bit for the outboard? Single and double seats are not what I have.

I’m happy to have a bit a F1 Lotus technology on board! Been watching how to fibreglass ply so I can get the job done. Are your ones the same length as the original?

This is mine at home.
You do not have the required permissions to view the files attached to this post.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.