Morning all
I was wondering if someone could give me a rough weight figure for a 535 on a galvanized single axle trailer with a 60hp Yamaha 2 stroke triple, I'm trying to decide what tyres to get and need to work out the rating i should aim for. I would take it to a weigh bridge but the tyres will prob let go before i got there.
Any help would be most welcome.
Thanks grahame
535 weight
-
deeandmartin
- Posts: 99
- Joined: Sat Feb 26, 2011 12:42 pm
- Location: No boat at present based in Mid Wales
Re: 535 weight
Have a look at the specs pages which give you the very basic weight of a 535, then suggest you do a search on the Internet the the type and size of engine, if you are also going to have general "stuff" on board like fuel tanks, fuel, and all the general boat clobber don't forget to add that in. We had a trailer collapse on us even though it was purchased by the previous owner for the "package" we had, it's not much fun and we now have a much larger trailer than we actually need but prefer to err on the side of caution! Good luck and hope you get sorted, Dee
-
dellquay13
- Posts: 556
- Joined: Tue Mar 15, 2011 7:45 am
- Location: Pequod, F4 mk4, Milford Haven Marina
Re: 535 weight
Hi,
You will be around 750kg fully loaded and including the trailer with 10% added for errors, which is the maximum legal limit for an unbraked trailer.
There are loads of old threads about trailer loadings, see http://www.shetland.owners.org.uk/forum ... &ForumID=1
Hope this helps,
Chris
You will be around 750kg fully loaded and including the trailer with 10% added for errors, which is the maximum legal limit for an unbraked trailer.
There are loads of old threads about trailer loadings, see http://www.shetland.owners.org.uk/forum ... &ForumID=1
Hope this helps,
Chris
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
-
grahame31
- Posts: 2
- Joined: Wed Feb 22, 2012 1:40 pm
Re: 535 weight
Hi Dee and Chris thanks for your help, would you know where i should aim for to find out her age? There are two plates on the boat, a shetland one plus a cert one. I guess somewhere there are records?
Thanks
Grahame
Thanks
Grahame
-
dellquay13
- Posts: 556
- Joined: Tue Mar 15, 2011 7:45 am
- Location: Pequod, F4 mk4, Milford Haven Marina
Re: 535 weight
Hi Grahame,
The shetland plate should have a serial number stamped on it, and you can date it using the SOA thread at viewtopic.php?f=14&t=282
Chris
The shetland plate should have a serial number stamped on it, and you can date it using the SOA thread at viewtopic.php?f=14&t=282
Chris
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
-
Davey1000
Re: 535 weight
Re trailers, IMHO the number one problem is internal rusting of the hollow suspension arms of some makes of independent suspension units. If the suspension arms have plastic blanking plugs this makes the problem worse as once water gets in, it cannot get out. Nevertheless changes in atmospheric pressure and changes in temperature cause the units to "breathe" and this allows in oxygen to complete the rust triangle (for rusting to occur three things are needed (1) Iron. (2) Water. (3) Oxygen. Remove any one of these and there will be no rusting) If one has a trailer with such suspension arms the hollow arms can be filled with cement or better still cement and U shaped pieces of reinforcing bar.
Hubs are usually quite reliable as long as they are well greased but rusted dry bearings will fail within a short distance.
Tyres can be a problem especially in the smaller sizes but even 8" wheels can be upgraded with 6 ply rated tyres.
Ten inch wheels can be fitted with 4, 6, or 8 ply rated tyres and the latter will handle about a ton per axle.
The next common size is the thirteen inch wheel often fitted with the ubiquitous 165 x 13 tyre which is common on caravans and horseboxes.
Twelve inch wheels also exist and some Leyland Minis used these. It is possible to fit 155/70 R12 trailer tyres to these but the wheel nuts and studs will give trouble long before the tyres which can carry 900 kilos each! Unfortunately there is not enough metal to allow thicker studs to be installed in a genuine Leyland Mini rear hub.
Watch out for "sealed for life" ball-races as used on some lightweight continental trailers. With this type I now take the bearings out and remove the inside seals. I then pack the hub with grease and put the bearings back. It is also possible to drill and tap the hub to take a grease nipple. Done this way the bearings don't shatter and the wheels don't fall off! I jest not because one of those lightweight trailers did drop a wheel at the end of a long journey. It was only the spindle washer and the weight that kept the wheel in place! Amazingly it was still possible to reclaim the hub just by fitting new bearings but a nasty gouge in the spindle needed to be built up by welding. Even so with the modifications of extra grease and the grease nipples the end result was better than new.
On the bigger trailers Land Rover Defender wheels are superb, the big tyres can carry up to two tons per axle and the low speed of rotation makes the bearings last for many years. Good luck!
Hubs are usually quite reliable as long as they are well greased but rusted dry bearings will fail within a short distance.
Tyres can be a problem especially in the smaller sizes but even 8" wheels can be upgraded with 6 ply rated tyres.
Ten inch wheels can be fitted with 4, 6, or 8 ply rated tyres and the latter will handle about a ton per axle.
The next common size is the thirteen inch wheel often fitted with the ubiquitous 165 x 13 tyre which is common on caravans and horseboxes.
Twelve inch wheels also exist and some Leyland Minis used these. It is possible to fit 155/70 R12 trailer tyres to these but the wheel nuts and studs will give trouble long before the tyres which can carry 900 kilos each! Unfortunately there is not enough metal to allow thicker studs to be installed in a genuine Leyland Mini rear hub.
Watch out for "sealed for life" ball-races as used on some lightweight continental trailers. With this type I now take the bearings out and remove the inside seals. I then pack the hub with grease and put the bearings back. It is also possible to drill and tap the hub to take a grease nipple. Done this way the bearings don't shatter and the wheels don't fall off! I jest not because one of those lightweight trailers did drop a wheel at the end of a long journey. It was only the spindle washer and the weight that kept the wheel in place! Amazingly it was still possible to reclaim the hub just by fitting new bearings but a nasty gouge in the spindle needed to be built up by welding. Even so with the modifications of extra grease and the grease nipples the end result was better than new.
On the bigger trailers Land Rover Defender wheels are superb, the big tyres can carry up to two tons per axle and the low speed of rotation makes the bearings last for many years. Good luck!
-
CaptainPhaff
- Posts: 16
- Joined: Tue Jul 23, 2013 6:33 pm
Re: 535 weight
Dear all - for those interested in 535 weights, you might be in for a shock like I was. I brought my boat from a marine trader, who assured me it was well within the weight limit for an un braked trailer. However, on the local weighbridge this morning it tipped the scales at 880kg! Weighed with a 1990 60hp 2 stroke mariner, a little bit of fuel and the anchor as the only heavy bits on the boat. The boat overhangs the trailer at the back by about 50cm so the trailer itself is quite small so I can't imagine it weighs that much. Time to look at the options for getting it restored as a braked unit - which is what it was originally.
Cheers
Cheers
-
daveg
- Posts: 2
- Joined: Mon May 20, 2013 10:32 am
Re: 535 weight
I have always thought that the 363Kg weight quoted for a 535 seemed low compared to other similar sized boats.
Is there a big difference in construction between the 535 and the 536 variants that seem to be around 580Kg?
Is there a big difference in construction between the 535 and the 536 variants that seem to be around 580Kg?
-
CaptainPhaff
- Posts: 16
- Joined: Tue Jul 23, 2013 6:33 pm
Re: 535 weight
Around 580kg would make sense for the boat alone as I understand that the engine is 112kg - that would leave the trailer and the other bits that were on the boat equaling about 200kg. I am about to order all the new bits to return the trailer to it original braked status - total cost for new axle, coupler and other bits are about £600 - ouch! Still, I need to do it if I am going to trailer the boat to Cornwall for some sea use before the summer is finished!