recently purchased 535, in need of advice

Thoughts, Ideas and General Questions
markgourlay1
Posts: 4
Joined: Wed Nov 21, 2012 5:31 pm

recently purchased 535, in need of advice

Post by markgourlay1 »

hi i'm new to the boating world, bought myself a shetland 535, i have a few questions regarding some stuff with it.
The boat did not come with a captain seat so i purchased one during the week with a pedestal. i have been out looking at the floor of the boat and realised its at a slight angle. im wondering if anyone could give me some advice on how to fix the pedestal to the floor.
Also i have been looking at other 535's and noticed that the windows are held in with rubber seals. The windows on my boat seem to be fitted with nuts and bolts then sealed onto outside of boat to stop water getting in. Any thoughts?
thanks mark :?:
jimbo3165
Posts: 5
Joined: Tue May 24, 2011 4:12 pm

Re: recently purchased 535, in need of advice

Post by jimbo3165 »

hi. sorry cant help with the seat but as for the windows, leave them bolted in. the rubber fitted ones are easy to push in especially at sea if hit by a big wave. hope that helps.
markgourlay1
Posts: 4
Joined: Wed Nov 21, 2012 5:31 pm

Re: recently purchased 535, in need of advice

Post by markgourlay1 »

hi jimbo3165, thanks very much for your reply about the windows.
As for fitting the pedestal to the floor, im still no further forward. Also been looking on the net but nothing seems too clear. I wouldnt just want to screw the pedestal to the floor as i have no clue whats underneath it and obviously just dont want them ripping out. Im thinking of trying to fix another piece of marine ply to the floor( a bit bigger than pedestal base) with some sort of adhesive then screw it down as well. Then fitting the pedestal to it for some extra support.
Hopefully someone on forum can steer me in the right direction.
StevieP
Posts: 41
Joined: Tue Aug 14, 2012 11:59 am
Location: Speedwell, Norfolk 'n' Wey, Oulton Broad, Suffolk

Re: recently purchased 535, in need of advice

Post by StevieP »

Hi Mark,
I found the use of No More Nails Exterior is pretty good for bonding ply, as long as the surfaces are varnish free. I would advise wearing latex gloves while applying as its extremely hard to remove from the skin...infact its extremely hard to remove it from anything!! :lol: .
Hope this info is of some use.

Steve.
markgourlay1
Posts: 4
Joined: Wed Nov 21, 2012 5:31 pm

Re: recently purchased 535, in need of advice

Post by markgourlay1 »

Hi steviep, thanks very much for advice. I have spoken to a joiner who is going to build a base for me and then i will use no more nails exterior plus a lot of screws to fix it to the floor so hopefully this will hold as i don' t want any accidents!
Mark.
User avatar
Coddy
Posts: 96
Joined: Thu Sep 01, 2011 3:51 pm
Location: Dorset

Re: recently purchased 535, in need of advice

Post by Coddy »

Be very careful when screwing down anything on the 535 as the boat skin is on a single thickness and you don't want to put holes in the bottom of the boat! :naughty:

I replaced the floor in my 535 by covering the whole floor area not just the centre section using 12mm marine ply, sealed both sides with polyester resin to prevent water ingress. You will need to add supports due to the shape of the floor, as you say it slopes inwards on both sides.

Your ply base can then be fixed onto your new floor and the pedistal mounted onto the wood base.

Hope that all makes sense.

Dave
:like:
markgourlay1
Posts: 4
Joined: Wed Nov 21, 2012 5:31 pm

Re: recently purchased 535, in need of advice

Post by markgourlay1 »

makes perfect sense. thanks very much for your advice dave :like: