A significant day

Thoughts, Ideas and General Questions
Deaks
Posts: 71
Joined: Sun Dec 02, 2012 6:31 pm
Location: 'Fortune', Black Hawk, Harrogate

A significant day

Post by Deaks »

Last Sunday was a significant day in that I finished removing the last scrap of paint from Fortune.
A late decision to strip the whole hull (as opposed to just above the waterline) made it a bigger job than first planned - I reckon somewhere between 40 and 50 hours in total.
Up to press every single thing I've done has been destructive - now I can look forward to repaint and rebuild.
I've even splashed a bit on the stern already.

Image

Image

Image

Image

To those who want to know how I stripped the bits obscured by the trailer - I jacked her up, placed some purpose made stands under her, and dragged the trailer out from under. Took an hour every time I did it and I was never confident enough to leave things that way overnight, so put her back on the trailer after every session. My neighbours think I'm nuts. Working under a half ton boat supported on stands you've made you very aware of your mortality!

Deaks
gwtyler
Posts: 4
Joined: Tue Mar 15, 2011 12:30 pm

Re: A significant day

Post by gwtyler »

well hope to see more photo,s as you go on with your painting
User avatar
davidemania
Posts: 95
Joined: Tue Mar 05, 2013 6:15 pm
Location: Monfalcone, eastern north Italy

Re: A significant day

Post by davidemania »

How did you strip the old paint? Sandpaper or chemicals?

It is not clear from the pictures, did you expose the fiberglass or is just the gelcoat having that sort of greenish color?

A plus for your courage, tough but good work!
Deaks
Posts: 71
Joined: Sun Dec 02, 2012 6:31 pm
Location: 'Fortune', Black Hawk, Harrogate

Re: A significant day

Post by Deaks »

It was so bl**dy cold when I started that strippers didn't work at all. They do now, though, as it's warmed up a bit.
It was essential to use strippers on the textured bits topsides (impossible to sand) but I would have found it much easier if I'd left them until the weather got better.
The nasty anti-foul stuff beneath the waterline is toxic if inhaled and shouldn't be sanded, so i scraped it off with a chisel. It's comes off in flakes like giant glitter which I caught and disposed of. What was beneath, plus all the other paint, was sanded with a fairly large random orbital sander. The only snag to a big sander is that it's hard to hold over your head for long periods when your under the boat. I've put lots of pictures in an earlier post.
A 120 grit disc was rough enough to take away the layers of paint but didn't penetrate the gelcoat, as long as I paid attention to what I was doing. As it happens the paint manufacturers specify sanding to 120 anyway as a surface preparation.
The gelcoat colour is the paler green you can see in all the photos. The darker green, mottled effect is from the first paint ever applied to the hull. There's not much left but I'd like to leave it where I can, as it shows I haven't penetrated the gelcoat.
I've done a few test patches, painting over the mottled bits with two-pack primer, and it hasn't reacted.
The whole process of stripping the lower hull was forced on me when I found a sizeable hole just on the waterline. It had been repaired but had gone porous. I reasoned that if there was one leaky hole there could be more, so stripped the lot to make sure. Naturally that was the only one.
I have to say that Shetland did a great job. In general the hull and superstructure are about perfect. I fancied simply polishing her up, but the Captain insisted we paint. No doubt she will decide on a different colour scheme for next season and I'll have to do it again.

Deaks
Deaks
Posts: 71
Joined: Sun Dec 02, 2012 6:31 pm
Location: 'Fortune', Black Hawk, Harrogate

Re: A significant day

Post by Deaks »

A few photos of Fortune defying gravity while I stripped the hull.

Image

Image

Image

Image