Hi all,
I have a Shetland family 4 that i'm going to start as a project with a couple of friend.
Basically, it was my late father's and is currently located in Northwest France. I was planning to scrap it as it's in a very poor state, but after chatting to a few frends, we have decided to take it on as project.
In a nutshell, it hasn't been in the water for approx 15 years and is sitting in my dads garden on a trailer. I have some fond memories of using it up and down the river medway as a teenager and as i'm almost 40 now, thats shows how long ago that was.
http://oma.sysg.net/photobucket/DSCF2097.JPG
http://oma.sysg.net/photobucket/DSCF2100.JPG
http://oma.sysg.net/photobucket/DSCF2077.JPG
All three of us are competent Engineers, but there is no escaping, it's going to take us a while as we all have young families.
We went and looked at Cuxton marina today in a dry dock to start with so we can work on it.
Basically, i'm after some hints and tips. Listed below in no particaular order is my current thoughts;
1. Clean the hull. What is best used for this?
2. The outboard. It's a Yamaha 75 2 stroke. One of my friend is good with engine, so hopefully he can sort that. I seem to remember my Dad having a "test prop" in a bucket of water, no sure where that is now.
3. All the carpet is past it, so I will want to replace it all.
4. Steering is struck, guessing I can replace the wires
5. Will need to replace the seats inside and out.
Is there a good place to look for parts?
Many thanks all
Shetland family 4 renovate
-
Coddy
- Posts: 96
- Joined: Thu Sep 01, 2011 3:51 pm
- Location: Dorset
Re: Shetland family 4 renovate
Hi Gareth
I would suggest a good power wash first and look for any cracks/holes in the hull
If all good then strip out the inside but keep any bits that can be used as templates, ie wood seat bases cushions etc.
The steering can be replaced and I would suggest a Teleflex cable instead of the wire system, this link might be useful for measuring the correct length required http://www.sailfishmarine.com/doc/measu ... cables.pdf
Look on EBay or this forum for parts for sale for seats and other fittings
The trailer will need a good service/check over as well before you put it on the road as I suspect the wheel bearings and brakes (if fitted) will have all rusted up and tyres cracked etc.
Looks a good project going by the pictures and if the engine can be got up and running it should be good fun to use.
Just had a second look at the pictures and it would appear that there is, what is left of, a keel band. This will need to be removed and to see if any water damage to the hull.
You may also find the floor in the cockpit is soft and may well need replacement, this is not to dificult to do but if you know anyone who knows how to fibreglass properly then they will be very useful.
I am sure you will get loads of help from this forum so ask away any questions
Look forward to hearing how you all progress and seeing some pictures as you go will make an interesting thread.
Dave
I would suggest a good power wash first and look for any cracks/holes in the hull
If all good then strip out the inside but keep any bits that can be used as templates, ie wood seat bases cushions etc.
The steering can be replaced and I would suggest a Teleflex cable instead of the wire system, this link might be useful for measuring the correct length required http://www.sailfishmarine.com/doc/measu ... cables.pdf
Look on EBay or this forum for parts for sale for seats and other fittings
The trailer will need a good service/check over as well before you put it on the road as I suspect the wheel bearings and brakes (if fitted) will have all rusted up and tyres cracked etc.
Looks a good project going by the pictures and if the engine can be got up and running it should be good fun to use.
Just had a second look at the pictures and it would appear that there is, what is left of, a keel band. This will need to be removed and to see if any water damage to the hull.
You may also find the floor in the cockpit is soft and may well need replacement, this is not to dificult to do but if you know anyone who knows how to fibreglass properly then they will be very useful.
I am sure you will get loads of help from this forum so ask away any questions
Look forward to hearing how you all progress and seeing some pictures as you go will make an interesting thread.
Dave
-
Gareth
- Posts: 5
- Joined: Thu Jul 11, 2013 9:03 pm
- Location: Kent, UK
Re: Shetland family 4 renovate
Hi,
Many thanks for your reply.
Re the trailer, as it had sunk a few inches in Dads garden, I suspected it to be all seized and tyres flat. When I was there last weekend, I jacked it up and was amazed to find 40psi in both tyres and the wheels spun freely. However, pulling the handbrake, there was a crack and the cable broke. It was so rusty, i'm not surprised.
I was thinking, I don't think it is a braked trailer (seem to remember dad always saying that), it just has a handbrake (or did) and a damper. The damper seems a bit stiff, ie it stayed compressed when I revered it back into position. I think i'll remove this next month when I'm there to clean it up at home.
For the hull, I thought i'd remove everything, even the stickers and the keel band and start again. What can I use for this, I remember dad using some special striper or liquid?
With the cabin as you say, not sure about the floor and haven't ventured in there yet;
http://oma.sysg.net/photobucket/DSCF2080.JPG
I was planning of stripping the whole lot out. I noticed last winter it had about an inch of water in the bottom, so the carpet is pretty ugg. It again might be better to start again. (just thinking in my head, wondering if there and companies out there that can build an interior, seats, etc). We're happy doing engines, bodywork, wiring, etc, but not very good at coachwork and trimming
The bottom line for me, is that even if it takes us a while, we haven't lost anything apart from the dry dock cost. From what I have read, I need to make sure the engine is okay as this is the most expensive part, so that might be a priority. As the Dry dock is a cheap one, it has no water and power. So, maybe I should test the engine when it's at my house.
Thanks again
Gareth
Many thanks for your reply.
Re the trailer, as it had sunk a few inches in Dads garden, I suspected it to be all seized and tyres flat. When I was there last weekend, I jacked it up and was amazed to find 40psi in both tyres and the wheels spun freely. However, pulling the handbrake, there was a crack and the cable broke. It was so rusty, i'm not surprised.
I was thinking, I don't think it is a braked trailer (seem to remember dad always saying that), it just has a handbrake (or did) and a damper. The damper seems a bit stiff, ie it stayed compressed when I revered it back into position. I think i'll remove this next month when I'm there to clean it up at home.
For the hull, I thought i'd remove everything, even the stickers and the keel band and start again. What can I use for this, I remember dad using some special striper or liquid?
With the cabin as you say, not sure about the floor and haven't ventured in there yet;
http://oma.sysg.net/photobucket/DSCF2080.JPG
I was planning of stripping the whole lot out. I noticed last winter it had about an inch of water in the bottom, so the carpet is pretty ugg. It again might be better to start again. (just thinking in my head, wondering if there and companies out there that can build an interior, seats, etc). We're happy doing engines, bodywork, wiring, etc, but not very good at coachwork and trimming
The bottom line for me, is that even if it takes us a while, we haven't lost anything apart from the dry dock cost. From what I have read, I need to make sure the engine is okay as this is the most expensive part, so that might be a priority. As the Dry dock is a cheap one, it has no water and power. So, maybe I should test the engine when it's at my house.
Thanks again
Gareth
-
Gareth
- Posts: 5
- Joined: Thu Jul 11, 2013 9:03 pm
- Location: Kent, UK
Re: Shetland family 4 renovate
I've just learnt about these "rabbit ears" to run the motor when it's dry. Oh, how things have moved on 
-
Coddy
- Posts: 96
- Joined: Thu Sep 01, 2011 3:51 pm
- Location: Dorset
Re: Shetland family 4 renovate
Hi Gareth
I am not sure if you are based in France or you have brought the boat back to the UK but before you start stripping everything do take plenty of detailed pictures so you can see where everything was before you started.
I would agree that the engine is an expensive part but it depends on where you wish to use the boat.
If on the sea then the 75hp would seem ideal but if on the river or canal then it may be a bit overkill, not sure about the river/canal regs in France if that's where you intend to keep her.
You can always sell the engine for a newer model, modern new 4-strokes are much more economical than old 2-strokes but they are heaver.
Again the 2nd hand market is full of "used bargains" but you do need to be careful you are not buying a load of trouble. I am sure Dave of Glasgow can suggest some good used engines for sale where he works and even some guidelines when looking for an engine.
To remove the anti-foul there are some dedicated removing gel/paint, alternative is to sand it down but you MUST do this with wet sanding blocks and wear protective breathing masks as it is not good stuff to breath in and the dust is even worse, but what every way you go it is going to get messy. There are plenty of useful sites which give advice on how to tackle this. One good one is here http://www.smlmarinepaints.co.uk/
Regarding the rest of the hull, after a good wash and scrub you could try using a fine cutting compound such as Farecla G3, with a power mop/sponge and again water mix this will remove all the dirt and grime in the gel coat and with any luck bring it back like new, well almost! You will then need to go over it all again with a good quality wax polish.
Dave
I am not sure if you are based in France or you have brought the boat back to the UK but before you start stripping everything do take plenty of detailed pictures so you can see where everything was before you started.
I would agree that the engine is an expensive part but it depends on where you wish to use the boat.
If on the sea then the 75hp would seem ideal but if on the river or canal then it may be a bit overkill, not sure about the river/canal regs in France if that's where you intend to keep her.
You can always sell the engine for a newer model, modern new 4-strokes are much more economical than old 2-strokes but they are heaver.
Again the 2nd hand market is full of "used bargains" but you do need to be careful you are not buying a load of trouble. I am sure Dave of Glasgow can suggest some good used engines for sale where he works and even some guidelines when looking for an engine.
To remove the anti-foul there are some dedicated removing gel/paint, alternative is to sand it down but you MUST do this with wet sanding blocks and wear protective breathing masks as it is not good stuff to breath in and the dust is even worse, but what every way you go it is going to get messy. There are plenty of useful sites which give advice on how to tackle this. One good one is here http://www.smlmarinepaints.co.uk/
Regarding the rest of the hull, after a good wash and scrub you could try using a fine cutting compound such as Farecla G3, with a power mop/sponge and again water mix this will remove all the dirt and grime in the gel coat and with any luck bring it back like new, well almost! You will then need to go over it all again with a good quality wax polish.
Dave
-
davidemania
- Posts: 95
- Joined: Tue Mar 05, 2013 6:15 pm
- Location: Monfalcone, eastern north Italy
Re: Shetland family 4 renovate
According to your pictures it seems your boat is basically identical to my 498 (there are minor differences in the cockpit but the hull and general structure appears to be the same). After 4 months of hard work I'm about to finish restructuring mine, I made major repairs on it so I can give you information on "hidden" parts if you need them
To start I would suggest to check the cored parts (expecially the roof and the bow) for water leaks, rotten core and delamination. The oles for the screws of the two large handles on the roof are probably drilled trough the core, on my boat this caused a disaster and required removing all the core (it is balsa wood) and a major rebuilding.
On my 498 the floor of the cockpit has been opened to create a storage space (adding all the necessary structural reinforcement of course) and from there it has been possible to expose the PU foam and let it dry. I don't know how yours is, but it could be worthy to check somehow for water leaks there. If the PU is soaked (should be closed cell but after so many years many things can change) you could easily add a large amount of unnecessary weight.
Check the bow part of the cabin and the bottom of the pit under the motor, may be you will find there iron rods glued to the resin, if they are rusted as in my boat it would be a nice job to remove them (they are useless).
To clean the boat, after powerwashing as it has already been suggested, I'd suggest HG hagesan blue (brought to my attention by someone on this forum), it works very well to remove limescale, algae and the like. You can get it from amazon UK for a fair price.
And, well, if you want to make me happy you could put a large piece of paper on the windshield (hope this is the correct word, I mean the transparent thing on top of the roof, just above the door, that protects you from breeze when you are moving) and take its shape. I'm in the process of building one for my boat from where it is missing, and having a very hard time finding the correct shape, with all those curved surfaces
Having a template would be invaluable!
From what I can say of mine, you'll find out there will be much more work than you initially thought, but you will enjoy it a lot and the result will be well worth the effort
I'll be glad to help in any possible way (btw I'm an engineer too
)
ciao
Davide
To start I would suggest to check the cored parts (expecially the roof and the bow) for water leaks, rotten core and delamination. The oles for the screws of the two large handles on the roof are probably drilled trough the core, on my boat this caused a disaster and required removing all the core (it is balsa wood) and a major rebuilding.
On my 498 the floor of the cockpit has been opened to create a storage space (adding all the necessary structural reinforcement of course) and from there it has been possible to expose the PU foam and let it dry. I don't know how yours is, but it could be worthy to check somehow for water leaks there. If the PU is soaked (should be closed cell but after so many years many things can change) you could easily add a large amount of unnecessary weight.
Check the bow part of the cabin and the bottom of the pit under the motor, may be you will find there iron rods glued to the resin, if they are rusted as in my boat it would be a nice job to remove them (they are useless).
To clean the boat, after powerwashing as it has already been suggested, I'd suggest HG hagesan blue (brought to my attention by someone on this forum), it works very well to remove limescale, algae and the like. You can get it from amazon UK for a fair price.
And, well, if you want to make me happy you could put a large piece of paper on the windshield (hope this is the correct word, I mean the transparent thing on top of the roof, just above the door, that protects you from breeze when you are moving) and take its shape. I'm in the process of building one for my boat from where it is missing, and having a very hard time finding the correct shape, with all those curved surfaces
From what I can say of mine, you'll find out there will be much more work than you initially thought, but you will enjoy it a lot and the result will be well worth the effort
I'll be glad to help in any possible way (btw I'm an engineer too
ciao
Davide
-
Gareth
- Posts: 5
- Joined: Thu Jul 11, 2013 9:03 pm
- Location: Kent, UK
Re: Shetland family 4 renovate
Hi guys, thanks for your replies.
Just to confirm, that I will be bringing my boat back to the UK first. The only thing i'll be doing in France is to make sure that it is roadworthy. I'll be bring it across the channel, on a trailer unfortunately, but it will be inside a big boat
(Caen to Portsmouth probably). Shame, as there is plenty of space in the garden in France including a barn that the boat will fit in.
I'm keen to get started and fortunately I have my wife behind me because it was my dads, which always helps, but I do realise it will take a very long time, especially when balancing work, family and everything else.
Not much I can do now, so i'm just gathering information and anything I can do up front. Looking at my work and personal diary (summer holidays are almost on us), beginning of September looks the best option. I have just brought a towbar for the wife's car (5 series bmw) as my little golf is not really heavy enough to pull it safely (and the clutch is not great).
@Dave. Re engine. I did find a web site, must have been "Dave of Glasgow". Maybe I thing about getting it serviced over the winter. Quite a long way from me though in the south
. I have been reading about starting a 2 stroke after it's been standing and in nutshell, they say soak it with Engine releasing agent and turn by hand with spark plugs out.
@Davide. I'd be more than happy to help you out. I looked at this windscreen last weekend and I will probably remove it before I transport it. It's held in from that I can see a bolt at either end, however, I noticed it was loose as the left hand screw had snapped off. Not sure how I will template it, but we can figure that out when I get it home
.
thanks again
Just to confirm, that I will be bringing my boat back to the UK first. The only thing i'll be doing in France is to make sure that it is roadworthy. I'll be bring it across the channel, on a trailer unfortunately, but it will be inside a big boat
I'm keen to get started and fortunately I have my wife behind me because it was my dads, which always helps, but I do realise it will take a very long time, especially when balancing work, family and everything else.
Not much I can do now, so i'm just gathering information and anything I can do up front. Looking at my work and personal diary (summer holidays are almost on us), beginning of September looks the best option. I have just brought a towbar for the wife's car (5 series bmw) as my little golf is not really heavy enough to pull it safely (and the clutch is not great).
@Dave. Re engine. I did find a web site, must have been "Dave of Glasgow". Maybe I thing about getting it serviced over the winter. Quite a long way from me though in the south
@Davide. I'd be more than happy to help you out. I looked at this windscreen last weekend and I will probably remove it before I transport it. It's held in from that I can see a bolt at either end, however, I noticed it was loose as the left hand screw had snapped off. Not sure how I will template it, but we can figure that out when I get it home
thanks again
-
Gareth
- Posts: 5
- Joined: Thu Jul 11, 2013 9:03 pm
- Location: Kent, UK
Re: Shetland family 4 renovate
Just to add.
Where is the best place to get parts? For example, if I wanted to get another pilot seat, is it eBay or is there a parts supplier. Could I buy a new one either from a third party or from Shetland direct? Someone at work suggest a caravan/camper upholsterer.
Bit of a way off, just thinking.
Where is the best place to get parts? For example, if I wanted to get another pilot seat, is it eBay or is there a parts supplier. Could I buy a new one either from a third party or from Shetland direct? Someone at work suggest a caravan/camper upholsterer.
Bit of a way off, just thinking.