shetland 535 ( pictures added )

Thoughts, Ideas and General Questions
richy904
Posts: 2
Joined: Wed Mar 05, 2014 6:00 pm

shetland 535 ( pictures added )

Post by richy904 »

Hi all looking to find how old my boat is I boaught ,, serial number that I found is 2748 ,,,he told me it was a 535 fastfisher if that is correct ,, I wasn't to happy with how low the back was so,, built her up a bit ,, I have a suzuki 85 on the back and it goes well....did try to add a picture but for some reason my phone won't allow it ,,,, if by any chance you wanted to see what I have done ,,, just email me [email protected] and just say pic and ill send one ,,, cheers for your help ,,richy
Last edited by richy904 on Fri Mar 07, 2014 4:37 pm, edited 1 time in total.
User avatar
admin
Site Admin
Posts: 862
Joined: Sat Feb 19, 2011 3:00 pm
Location: "Phonix" , Tuckton Basin, Christchurch

Re: shetland 535

Post by admin »

Richy - send the images to my admin email address [email protected] and I will post them for you

Sue
There is NOTHING--absolutely nothing--half so much worth doing as simply messing about in boats.
Kenneth Grahame
User avatar
admin
Site Admin
Posts: 862
Joined: Sat Feb 19, 2011 3:00 pm
Location: "Phonix" , Tuckton Basin, Christchurch

Re: shetland 535

Post by admin »

IMG-20140219-00120.jpg
IMG-20140209-00113.jpg
You do not have the required permissions to view the files attached to this post.
There is NOTHING--absolutely nothing--half so much worth doing as simply messing about in boats.
Kenneth Grahame
User avatar
bobtooke
Posts: 110
Joined: Sun Aug 11, 2013 11:26 pm
Location: South London / Newhaven

Re: shetland 535 ( pictures added )

Post by bobtooke »

HI Richy, I think that you will find your boat number listed in the spec.s section so you will be able to tell the rough age. At least you have a number, mine didn't!
Looks very good with the higher freeboard on it. A few people criticize the 535 for the low sides. How did you make up the sides? I can see it's done with GRP but how did you mold it?
"Don't worry, I'm completely lost too"
Currently aboard "Sweet Kismet", Shetland 535 / Honda 50

Experts in freshwater treatment to the marine industry.
http://www.amphibia.co.uk
richy904
Posts: 2
Joined: Wed Mar 05, 2014 6:00 pm

Re: shetland 535 ( pictures added )

Post by richy904 »

Cheers for the info ,,, made the mold out off ,, 2 laminate floor boards . Lengh of 2 by 1 inch wood ,, clingfilm ,, nd a screw fix book ,,lol... Cut the shape out I needed for the side panel , then cut the lamin floor boards ,, cut the 2 by 1 inch wood to fit for the tops , and the screw fix book placed in between the two boards ,,, cling filmed it all over ,, then just fibreglassed over what I had made ,,, hope this makes scence so far ,, the screw fix book lol ,, was what I had down my shed at the time and was 2 inches wide ,,, when I pulled the book out ,, the boards colapesd and just pulled the mold out ,, then just made up a sheet off fibreglass that would fit across the back joining to the 2 side panels , a lengh of 3 by 1 for strengh across the top again to join up with the side panels ,, then just taped it all to the boat , after a good sand back ,,and just useing fibreglass bandage ,,atatched it to the boat ,,, just wish , my painting skill with 2 pack were a bit better ,, but the boat feels safer and that's what I wanted to do ,,, I hope it all makes scence ,, richy