Family Four Engine Size
-
bobDD
- Posts: 2
- Joined: Thu Mar 06, 2014 7:24 pm
Family Four Engine Size
Hi, I am a very proud owner of a shetland family four which came with an old 2 stroke 40hp mercury engine. I'm going to replace the engine and ive found a mariner 60hp 4 stroke efi ptt 2004. Would this engine get her on the plan out to sea and what sort of speed would i achieve. Any advice would be great full. Bob 
-
rbmatthews
- Posts: 106
- Joined: Tue Mar 15, 2011 9:02 am
- Location: Northeast Scotland
Re: Family Four Engine Size
Hi BobDD
Good choice! We have an F4 too.
The F4s should take an engine up to 80hp, so a 60 hp is fine in that respect. As far as performance is concerned, I am not familiar with that particular engine (there are probably others here who are), but as a comparison we have a Mariner Optimax 75 hp and that has no problems at all in planing and does about 25 knots at wide open throttle. We use ours exclusively in the sea. A 60 hp might be slightly less than this, but probably not a lot. You need to make sure too that you get the right propellor specification for your engine/boat configuration.
See http://shetlandf4.wordpress.com/main-engine/ for more details.
Hope this helps
Robin.
Good choice! We have an F4 too.
The F4s should take an engine up to 80hp, so a 60 hp is fine in that respect. As far as performance is concerned, I am not familiar with that particular engine (there are probably others here who are), but as a comparison we have a Mariner Optimax 75 hp and that has no problems at all in planing and does about 25 knots at wide open throttle. We use ours exclusively in the sea. A 60 hp might be slightly less than this, but probably not a lot. You need to make sure too that you get the right propellor specification for your engine/boat configuration.
See http://shetlandf4.wordpress.com/main-engine/ for more details.
Hope this helps
Robin.
Swannanoa, 1989 Shetland Family Four
http://shetlandf4.wordpress.com
http://shetlandf4.wordpress.com
-
daveingartcosh
Re: Family Four Engine Size
a 60hp is perfect. even better if it is not the bigfoot model and I was getting 30mph
RB is your opti running right? your performance is low for that engine on that boat so check the revs please and do a compression test. Obviously ignore if you have 4 people and are carrying a v heavy load.
RB is your opti running right? your performance is low for that engine on that boat so check the revs please and do a compression test. Obviously ignore if you have 4 people and are carrying a v heavy load.
-
bobDD
- Posts: 2
- Joined: Thu Mar 06, 2014 7:24 pm
Re: Family Four Engine Size
Thanks guys for your posts, If we can get 30mph that would be great
. I'm off to look at the engine on sunday so fingers crossed its a good one.
-
rbmatthews
- Posts: 106
- Joined: Tue Mar 15, 2011 9:02 am
- Location: Northeast Scotland
Re: Family Four Engine Size
Daveingartcosh
Boat was fairly well laden with two people, full fuel tanks (80 litres), auxilliary engine, two batteries, and enough food, water and personal gear for almost two weeks. It manages 25 kts quite easily at that. I can't remember if it was exactly WOT, so it possibly could do more, but will check more accurately when it goes back in the water. Prop is a 13″ x 15″. Compressions are all good at 110 psi last time I measured them.
R.
Boat was fairly well laden with two people, full fuel tanks (80 litres), auxilliary engine, two batteries, and enough food, water and personal gear for almost two weeks. It manages 25 kts quite easily at that. I can't remember if it was exactly WOT, so it possibly could do more, but will check more accurately when it goes back in the water. Prop is a 13″ x 15″. Compressions are all good at 110 psi last time I measured them.
R.
Swannanoa, 1989 Shetland Family Four
http://shetlandf4.wordpress.com
http://shetlandf4.wordpress.com