Shetland 535 refurb step by step

Thoughts, Ideas and General Questions
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

Thanks for the kind comments everyone.

From this point onwards I take no responsibilty for which way up my photos appear.

Right - onwards. The latest focus is the windows. As a test, I made a port light to go in the roof hatch. A simple disc of 5mm Perspex with two p-seals; one around the hole in the hatch and one around the edge of the Perspex. All clamped together with a ring of plastic bolts. Time will tell if this design is watertight.

This test proved that my Bosch acrylic jigsaw blades and ordinary Guhring drill bits are perfectly adequate and efficient for working 5mm Perspex.

Next its on with the windows. Gulp.
You do not have the required permissions to view the files attached to this post.
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

As you may have realised from the previous post, I have decided to go with bolted in windows. I know this is not standard on the 535 but it is a more robust solution, more suited to offshore environments. I'm not particularly intending to go in search of "green water" situations but I do have some offshore ambitions so it seems the wise choice.

Besides this, fitting bolted in windows is less difficult, especially for a very early model like mine (actually an "Escomar Shetland" ) which has differently shaped windows compared to a later 535, so windows and seals are less readily avaliable 'off the shelf'.

I've heard it said that doing this will devalue the boat but, come on, this is a low-cost fiberglass boat from the 1970s. It's not a quarter-million pound Riva, or even a Storebro.

I hope this will make the boat more seaworthy and, if I execute it well-enough, more desirable (to some people) than the standard spec. Not that I have any intention of selling her... :D

So, stay tuned for the windows - a project in itself!
Last edited by Whammers on Sat Nov 07, 2015 7:31 am, edited 3 times in total.
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

After much research, I decided on 5mm thick acrylic (Perspex) for the windows. They would need to be 30mm bigger all round than the old windows to allow for the overlap required for bolting them. I went for dark grey tint to cut down on UV degradation, which wasn't what my other half Gill preferred but I somehow convinced her that it was the most practical colour. It looks great as well! ;)

I bought a sheet of 1m x 1m for the front windows and a sheet of 1m x 1.5m for the side windows from Trent Plastics online. Not cheap at £135 but delivery was fast and I was soon busy marking out ready for the cutting out.

I approached this with some trepidation but in fact it is an easy material to work with and I soon had four reasonable windows.
You do not have the required permissions to view the files attached to this post.
vreagh
Posts: 327
Joined: Sat Aug 02, 2014 5:46 pm
Location: Cornwall

Re: Shetland 535 refurb step by step

Post by vreagh »

Hi,Good choice to replace windows with acrylic,you will feel much safer in a lumpy sea. I`ve replaced my early shetland`s twice.The first time I used countersunk screws. It seems the taper on the head puts side force on the acrylic which eventually causes splits to radiate outwards with the slight flexing of the boat. Next time I used 6mm pan heads with washers under the heads this has cured the problem,but..... I used stainless A2 slotted screws,and the sharpness of the slot plays havoc with clothing when moving around the deck.When ??? I get round to it, I`ll replace them with crossheads. Hope this helps. Keith
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

Cheers Keith. I did a lot of readng before finalising the spec of the windows and picked up on the countersunk screw issue. This is what I've decided to do..

The windows will have an EPDM p-seal around the outer edge. Inside that are the bolt holes and a 19mm wide strip of double-sided neoprene tape, covering the inside of the holes. This tape is incredibly sticky and some people have used it to fit their windows, with no bolts at all!

I'm not quite that confident in it so mine will have bolts but my bolts will be nylon; strong enough, slightly flexible and totally corrosion proof. They are M6x25mm - actually they are number plate mounting bolts (around £6 for 100 with nuts). :D

To seal under the heads I bought 100 M6 rubber o rings but when they arrived they seemed very small and 'weedy'. I wasn't sure about them but, working in the Materials Engineering department of a major aircraft manufacturer it was easy enough to take bolts nuts o rings and a piece of scrap acrylic to work for a 2nd 3rd and 4th opinion.. We bolted it all together and it was pronounced a suitable solution.
Onward!
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

These pics (whichever way up they appear) show screw, o ring and nut, and the inside of the window edge (with protective materials still in place) showing the p-seal, neoprene tape, and a screw to show their position.
You do not have the required permissions to view the files attached to this post.
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

The holes were spaced in what seemed a logical way - 26 in each side window and 18 in each front window. They were then drilled with an ordinary hss drill bit to 6mm. The windows were then carefully positioned and held in place with masking tape. Two holes at 5.5mm were then drilled through the cabin sides and two screws put through to hold the windows securely. The rest of the 5.5mm holes were then drilled through.
You do not have the required permissions to view the files attached to this post.
Last edited by Whammers on Fri Nov 20, 2015 7:01 am, edited 1 time in total.
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

My plan is to stick the windows in place with the double sided tape using a couple of screws for location then simply install the rest of the screws and nuts. The screws should compress the p-seal nicely. The key will be to avoid over tightening them. I say simply but I am a one-armed man working alone so this will prove challenging.

Also, I will need a dry day.. : :roll:
You do not have the required permissions to view the files attached to this post.
Last edited by Whammers on Thu Jan 14, 2016 10:35 pm, edited 2 times in total.
User avatar
bobtooke
Posts: 110
Joined: Sun Aug 11, 2013 11:26 pm
Location: South London / Newhaven

Re: Shetland 535 refurb step by step

Post by bobtooke »

Fantastic job so far. I think you made the right choice in window fixings with those plastic screws. Personally I think I would seal the bolts in using a few blobs of silicone sealant.

I'm looking forward to seeing the final result though and considering copying you!
:mrgreen:
"Don't worry, I'm completely lost too"
Currently aboard "Sweet Kismet", Shetland 535 / Honda 50

Experts in freshwater treatment to the marine industry.
http://www.amphibia.co.uk
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

Cheers Bob, I'm happy to be the guinea pig on this... :D

Sadly, all work on the boat is currently at a standstill due to the hideous weather. I can't even do bits and bobs at home because my garage is flooded. :cry:

I shall wait and twiddle my thumb until the storms pass.