Shetland 535 refurb step by step

Thoughts, Ideas and General Questions
vreagh
Posts: 327
Joined: Sat Aug 02, 2014 5:46 pm
Location: Cornwall

Re: Shetland 535 refurb step by step

Post by vreagh »

Hi ,That`s a great idea to use number plate fixings. I think the blob of silicone may be good too.My Shetland mk11 has a 75hp Ford inboard which can vibrate at certain revs. The first window transplant used plain nuts which were forever slackening. The second time I used Simmonds nuts, this cured the problem but at a cost. I think I may have overdone the fixings....38 on each side 26 each front. Your solution is much neater. Hope your flooding clears and look forward to the next installment. Regards Keith
Barton
Posts: 17
Joined: Wed Nov 18, 2015 3:15 pm
Location: NORTH DEVON

Re: Shetland 535 refurb step by step

Post by Barton »

EvangelicalAtheist wrote:Great post which I will watch with interest. Has motivated me to also put a few pictures up of my restoration project. :P
Hi i have just bought my first boat is 535 not sure of year , I have had to take out deck and cabin floor ,question is there were no stringers just foam and remains of chipboard floor if there are stringers dose anyone know were they positioned in hull and what way do they run, (foam under deck and cabin floor }
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

See seperate thread for continuation of the deck conversation..

Well I've just had a dry (but bloomin cold) weekend and it has been a weekend of mixed fortunes...

I've succeeded in fitting the windows. The seals and bolts worked very well, though some bolts have stripped and will need to be replaced. The plastic is very soft and they only really need to be finger tight plus a tiny tweak. They seem to have squeezed the seals quite nicely though.

I also tried to fit the windscreen I bought from eBay but I have wires coming out of the roof for horn and nav light which get in the way. After considering my options I decided to take a half moon shaped section 25mm high out of the lower edge of the screen rather than drilling more holes in the cabin roof. Not easy to take the jigsaw to my new £120 screen but I think it will be the best solution overall. I also intend to re engineer the fixing method; the screen was supplied with rather unattractive coach bolts which were a long way from satisfying my fastener fetishes.. :D So, a new solution will be devised.
Meggy 061 front windows.jpg
Meggy 059 windows in.jpg
You do not have the required permissions to view the files attached to this post.
Last edited by Whammers on Mon Nov 23, 2015 2:05 pm, edited 2 times in total.
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

I was also hopng to fit hinges on the roof hatch. I bought some superb stainless pivot hinges but for some reason just assumed the mounting holes were M6 and bought fasteners in that size. When I came to start fitting them I discovered the holes are M5. Idiot!

So, another job that has had to be postponed.. :roll:
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

Well, it's been another foul weekend. I only made a quick trip to the boat to find the tarpaulin completely off and everything awash (as there's no roof hatch in place at the moment). It took two of us with a struggle to pull the tarp back into position in the wind, which was gusting 50 knots, er I mean 50 mph... We weighed it down with big stones, sand bags and breeze blocks but I don't know how long it will hold. I need to get her independently weather-tight but I need good weather for that!

Meanwhile, I'm busying myself getting the roof hatch details finished. Hinges are now attached, with neoprene tape to seal the mounting faces, and the newly cleaned up rubber hooks refitted, complete with repainted mounting brackets. The underside is now covered with closed cell foam, doubling as a seal and insulation but a finishing strip is still needed around the inside of the porthole.

I've also ordered a couple of gas struts to make it easier to lift from below. Swanky eh? :D
Meggy 067 hatch underside.jpg
Meggy 066 hatch hook.jpg
Meggy 065 hatch hinge.jpg
You do not have the required permissions to view the files attached to this post.
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

The other thing that has been occupying my time during the 'washout' is researching my options for a cockpit tonneau cover and, eventually, perhaps full canopy.

There are apparently two main materials to consider - PU coated acrylic canvas or PVC vinyl.  By all accounts, the synthetic canvas ('masacril') is far superior; longer lasting, tougher and more attractive. However, it is between 15% and 30% more expensive, depending on supplier. Prices quoted for a cockpit cover range from £125 to £255.  I've more or less decided that, for a cockpit cover the vinyl is probably quite serviceable and it would leave more money in the budget to spend elsewhere, like on the deck, interior, engine....

Fastenings for the cover are another conundrum. Meggy has standard hooks along the cockpit sides but no fixings on the cabin top at all. However, I've been learning all about the various options - press studs (poppers), turn buttons, lift the dot, hook and loop etc  and all are pretty easy to fit. Currently, I favour either turn buttons or lift the dot type fasteners. They will have to be stainless though - I don't want unsightly rust spoiling all my hard work!

Watch this space as I'm about to take the plunge. :o
vreagh
Posts: 327
Joined: Sat Aug 02, 2014 5:46 pm
Location: Cornwall

Re: Shetland 535 refurb step by step

Post by vreagh »

Hi, don't know if you're going to fit a windscreen but if you are, I've fitted poppers to top of screen as on the original hood fittings. The tonneau then goes from transom to screen with no puddling of water. This has been totally reliable even in winter gales whilst moored on trots. Top of screen fitted with some chrome plastic beading as fitted to outside of classic minis. This protects tonneau from abrasion. Regards Keith
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

Thanks Keith. The two suppliers I've spoken to so far say their tonneaus fit to the cabin behind the screen. I am going to fit a screen though so your method would be an option. Did you get your cover made or is it an off-the-shelf item?

Another general question is, do you tow with it in place? Samhoods say you mustn't tow with the cover on. I thought that was at least one of the tonneau's purposes?
Last edited by Whammers on Thu Jan 14, 2016 10:48 pm, edited 2 times in total.
vreagh
Posts: 327
Joined: Sat Aug 02, 2014 5:46 pm
Location: Cornwall

Re: Shetland 535 refurb step by step

Post by vreagh »

Hi , my tonneau is a one off which I replace ever 6 years or so. I've never tried towing with it as I only tow twice a year between the farm and harbour. Would have thought it's probably better to have the front fixing for tonneau below screen out of the main airflow.
Regards
Keith
Whammers
Posts: 134
Joined: Wed Sep 24, 2014 2:30 pm

Re: Shetland 535 refurb step by step

Post by Whammers »

Yes, I was thinking that the screen would provide a kind of fairing for the front edge of the cover. The sides are only hooked on with elastic straps so, for towing, a more secure fastening is probably wise.

I'm now thinking that eyelets in the cover and turn buttons on the topsides should be strategically positioned from cabin top and down cockpit sides to make sure the cover is secure. I envisage doing a fair bit of towing, though only at 50mph. It should be easy to keep the cover secure at that speed. After all, the soft top on my Alfa Spider is supposed to be OK up to 145mph. .. in theory. :shock:

Thanks Keith, you've helped me to decide the way forward. :D