hi all
I have a Shetland 610 1970s the plate says no.100, and have acquired a 90hp 2 stroke engine, I just wondered if it was ok to fit this engine and if so do I need to strengthen the transom or fit bassist ect. any help would be appreciated.
many thanks
ian
shetland 610 engine question
-
Stokey1964
- Posts: 164
- Joined: Sun Dec 07, 2014 1:54 pm
- Location: Stoke-on-Trent
Re: shetland 610 engine question
Our own website specs page say the 610 was rated to handle 120hp inboard or outboard
your boat looks like it was built between 1975 and 1976
Your 90 2 stroke will be fine, its more about weigh on the transom than size of the engine.
A 4 stroke 90hp for example could be 50 or more kilos heavier than a 90hp 2 stroke.
Simon
your boat looks like it was built between 1975 and 1976
Your 90 2 stroke will be fine, its more about weigh on the transom than size of the engine.
A 4 stroke 90hp for example could be 50 or more kilos heavier than a 90hp 2 stroke.
Simon
Shetland 570 MK 1
Yamaha 90 2006
Yamaha 90 2006
-
ian4610
- Posts: 8
- Joined: Thu Sep 29, 2016 1:22 pm
Re: shetland 610 engine question
that's great stokey1964, would putting ballast at the bow bring the stern up out of the water a bit?
it might sound like a stupid question but it has a 15hp 4 stroke at the minute and it seems to sit a bit low at the stern.
many thanks
ian
it might sound like a stupid question but it has a 15hp 4 stroke at the minute and it seems to sit a bit low at the stern.
many thanks
ian
-
Stokey1964
- Posts: 164
- Joined: Sun Dec 07, 2014 1:54 pm
- Location: Stoke-on-Trent
Re: shetland 610 engine question
I had a 50 4 stroke on mine (too small) and have a 90 2 stoke yam ready to go on.
even with the 50 it wasn't too low at the stern
the 15hp should be much lighter, so that doesn't sound right
are you sure you don't have water logged foam under the cockpit floor (cant say 100% that the 610 had foam between the floor and skin)
Do you have a rear drain plug on the transom that you can test for water, or any access points under the floor?
even with the 50 it wasn't too low at the stern
the 15hp should be much lighter, so that doesn't sound right
are you sure you don't have water logged foam under the cockpit floor (cant say 100% that the 610 had foam between the floor and skin)
Do you have a rear drain plug on the transom that you can test for water, or any access points under the floor?
Shetland 570 MK 1
Yamaha 90 2006
Yamaha 90 2006
-
ian4610
- Posts: 8
- Joined: Thu Sep 29, 2016 1:22 pm
Re: shetland 610 engine question
yes I can get under the floor and there is no water, but when I brought it there was quite a lot of water from a old unused sea cock, I removed that and glassed it over so there is no water on board now, not sure about foam but there is a drain. im taking it out of the water this wkend so I will remove it, does that drain between the skins simon?
thanks
ian
thanks
ian
-
Stokey1964
- Posts: 164
- Joined: Sun Dec 07, 2014 1:54 pm
- Location: Stoke-on-Trent
Re: shetland 610 engine question
It should drain out any water below the cockpit floor
It doesn't go between the skins
Simon
It doesn't go between the skins
Simon
Shetland 570 MK 1
Yamaha 90 2006
Yamaha 90 2006
-
ian4610
- Posts: 8
- Joined: Thu Sep 29, 2016 1:22 pm
Re: shetland 610 engine question
Ok thank you, I will try and move what I have on board around and see if that helps.