Never filled so many holes in my life
535 restoration project progress.
-
Robsaffer
- Posts: 11
- Joined: Wed Feb 15, 2023 4:53 pm
Re: 535 restoration project progress.
Hi Clive, I have been using Teroson UP620 Gelcoat Filler and the UP610, hopefully that is ok?
Never filled so many holes in my life
Never filled so many holes in my life
-
blebrocq
- Posts: 108
- Joined: Thu Oct 20, 2022 11:24 am
Re: 535 restoration project progress.
As Clive asked - where do you intend to use it. if inland waterways only you will find that engine to be way too big, it won't like going slowly, will foul it's plugs regularly, & use lots of fuel. (I know, I had a Black Hawk with a 60 2 stroke on it, no good on the waterways I wanted to use it on, so swapped for a 25Hp 4 stroke, halved the fuel bill, & engine ran all day at 5 MPH. If however you are planning on using it at sea, than that is a different matter.
Bob (I also now have a 4+2 !)
Bob (I also now have a 4+2 !)
-
vreagh
- Posts: 327
- Joined: Sat Aug 02, 2014 5:46 pm
- Location: Cornwall
Re: 535 restoration project progress.
The hull to deck joint on early boats used a few rivets just to hold everything in place before the joint was heavily glassed on the inside. This will be seen as what looks like a coving between deck and hull. This was not done on later boats and they relied on the mastic and rivets to hold eveything together. This is why you hear tales of water getting in through this joint, the early boats didn't suffer from this problem. If you post a pic of the joint from inside I can tell you what type you have.
-
Robsaffer
- Posts: 11
- Joined: Wed Feb 15, 2023 4:53 pm
Re: 535 restoration project progress.
Hopefully you can tell from these vreagh and thanks for your help!
You do not have the required permissions to view the files attached to this post.
-
Robsaffer
- Posts: 11
- Joined: Wed Feb 15, 2023 4:53 pm
Re: 535 restoration project progress.
Hi Bob,
I think it will be mostly at the coast and some inland use from time to time.
Thanks
Rob
I think it will be mostly at the coast and some inland use from time to time.
Thanks
Rob
blebrocq wrote: Sun Mar 05, 2023 4:57 pm As Clive asked - where do you intend to use it. if inland waterways only you will find that engine to be way too big, it won't like going slowly, will foul it's plugs regularly, & use lots of fuel. (I know, I had a Black Hawk with a 60 2 stroke on it, no good on the waterways I wanted to use it on, so swapped for a 25Hp 4 stroke, halved the fuel bill, & engine ran all day at 5 MPH. If however you are planning on using it at sea, than that is a different matter.
Bob (I also now have a 4+2 !)
-
vreagh
- Posts: 327
- Joined: Sat Aug 02, 2014 5:46 pm
- Location: Cornwall
Re: 535 restoration project progress.
Not that clear from the pics, but, to me that looks like a filler laid into the join. Older boat were glassed so it was all fibreglass smoothed onto the deck and hull with no edges and the curve much thicker. As Clive suggest, I think you would be wise to use more rivets or arrange for the gunwhale rubber fixings to help tie the two together.
-
Robsaffer
- Posts: 11
- Joined: Wed Feb 15, 2023 4:53 pm
Re: 535 restoration project progress.
Perfect, thank you, more rivet's it is then!!!