I've had my heart set on a little boat to nip around the canals and rivers near by and came across a hull of a Shetland 535.
It has no outboard or engine so my first question is what would I be looking at to put in a steering column and engine / outboard so I can get moving?
Furthermore whilst I'm due to go and have a look at said hull, and I will be hoping to take up the floor to inspect the interior fully, what other areas could be of concern.
Im a complete novice when it comes to boat technicalities, so any advice would be greatly appreciated.
I plan on doing all the work myself, maybe with a few beer bribes or just out right cash incentives along the way, but the hard graft I'm willing to undertake at weekends to (pardon the pun) make her ship shape and dandy. Really she's a project for the winter and then get her out in the summer.
Hope there's some advice out there,
Much appreciated,
James
Shetland 535 novice build
-
bobtooke
- Posts: 110
- Joined: Sun Aug 11, 2013 11:26 pm
- Location: South London / Newhaven
Re: Shetland 535 novice build
Hi James and welcome.
The 535 is a great little boat and although they are very old, there are still a lot around which is a good indicator of the build quality.
The main thing to check is the transom I would suggest. Make sure its solid and the wood inside hasn't rotted out. It can be fixed but can be an expensive job to do.
Apart from that just check the most obvious such as cracks, splits and poor repairs. A few little cracks in the gelcoat aren't much to worry about but if it extends through the GRP it will need further investigation.
You can get a steering helm and cable kit quite easily but maybe best to wait until you find a suitable outboard first so you can match it to the engine.
If you're just using it on rivers and canals you probably won't need too much power say, 25 to 35hp?
HTH
Bob
PS where are you based? Someone local may be able to offer help or advice.
The 535 is a great little boat and although they are very old, there are still a lot around which is a good indicator of the build quality.
The main thing to check is the transom I would suggest. Make sure its solid and the wood inside hasn't rotted out. It can be fixed but can be an expensive job to do.
Apart from that just check the most obvious such as cracks, splits and poor repairs. A few little cracks in the gelcoat aren't much to worry about but if it extends through the GRP it will need further investigation.
You can get a steering helm and cable kit quite easily but maybe best to wait until you find a suitable outboard first so you can match it to the engine.
If you're just using it on rivers and canals you probably won't need too much power say, 25 to 35hp?
HTH
Bob
PS where are you based? Someone local may be able to offer help or advice.
"Don't worry, I'm completely lost too"
Currently aboard "Sweet Kismet", Shetland 535 / Honda 50
Experts in freshwater treatment to the marine industry.
http://www.amphibia.co.uk
Currently aboard "Sweet Kismet", Shetland 535 / Honda 50
Experts in freshwater treatment to the marine industry.
http://www.amphibia.co.uk
-
Jshakespeare
- Posts: 2
- Joined: Mon Nov 10, 2014 11:10 pm
Re: Shetland 535 novice build
Cheers for the reply Bob
The transom is where the outboard sits correct? If there's play or obvious cracks ie the water has penetrated then it's likely it will have rotted - would that be fair to assume?
As for cracks and splits it's going to be largely what I can see correct. Should I be concerned with what is under the floor or will I be able to identify areas of concern from just looking at the outside.
With regards to the exterior, and having spoken with the current owner he says it could do with a sand down and re coat, would I be able to attack this with a power sander and light grain paper ready for a new coat, or is there other methods?
When you say about cracks in the gelcoat but extend into the GRP, what do you mean, and what is the GRP?
I'm based in Hertfordshire but relocating either to south west London or Guildford
J
The transom is where the outboard sits correct? If there's play or obvious cracks ie the water has penetrated then it's likely it will have rotted - would that be fair to assume?
As for cracks and splits it's going to be largely what I can see correct. Should I be concerned with what is under the floor or will I be able to identify areas of concern from just looking at the outside.
With regards to the exterior, and having spoken with the current owner he says it could do with a sand down and re coat, would I be able to attack this with a power sander and light grain paper ready for a new coat, or is there other methods?
When you say about cracks in the gelcoat but extend into the GRP, what do you mean, and what is the GRP?
I'm based in Hertfordshire but relocating either to south west London or Guildford
J
-
bobtooke
- Posts: 110
- Joined: Sun Aug 11, 2013 11:26 pm
- Location: South London / Newhaven
Re: Shetland 535 novice build
Well I'm no boat engineer but I'll help with what I know...
Yep, the transom is the flat bit at the back. If the wood inside the GRP has rotted it may not be cracked or obvious. The main ways to tell is to give it a good old shove and tug to see if it moves about. Also get inside under the splash well and see what sort of state its in there.
GRP is glass reinforced plastic and its the term for the glassfibre construction. Usually made up from a number of varying layers with a thin "gelcoat" as an outer skin. The gelcoat is smooth, hard wearing and resistant as opposed to the coarser fibre reinforced, stronger layers underneath which give the material its super strength.
As said, small hairline cracks in the gelcoat aren't too much of a worry and can be repaired easily but if the cracks are larger and extend into or through the reinforced layers its a bigger issue! Large gelcoat cracks can also be an indicator of a lamination failure underneath or poor repair so still worth investigating. Just look for bad cracks or bad repairs and if possible take along someone with some experience of boats and GRP.
Having said all that, Shetlands were very solidly made boats so even old girls like mine have survived well.
When repainting its always best to take the old paint off as much as possible but yes, scraping and sanding back with a power sander and recoating is easy enough to do if a little time consuming.
HTH
Yep, the transom is the flat bit at the back. If the wood inside the GRP has rotted it may not be cracked or obvious. The main ways to tell is to give it a good old shove and tug to see if it moves about. Also get inside under the splash well and see what sort of state its in there.
GRP is glass reinforced plastic and its the term for the glassfibre construction. Usually made up from a number of varying layers with a thin "gelcoat" as an outer skin. The gelcoat is smooth, hard wearing and resistant as opposed to the coarser fibre reinforced, stronger layers underneath which give the material its super strength.
As said, small hairline cracks in the gelcoat aren't too much of a worry and can be repaired easily but if the cracks are larger and extend into or through the reinforced layers its a bigger issue! Large gelcoat cracks can also be an indicator of a lamination failure underneath or poor repair so still worth investigating. Just look for bad cracks or bad repairs and if possible take along someone with some experience of boats and GRP.
Having said all that, Shetlands were very solidly made boats so even old girls like mine have survived well.
When repainting its always best to take the old paint off as much as possible but yes, scraping and sanding back with a power sander and recoating is easy enough to do if a little time consuming.
HTH
"Don't worry, I'm completely lost too"
Currently aboard "Sweet Kismet", Shetland 535 / Honda 50
Experts in freshwater treatment to the marine industry.
http://www.amphibia.co.uk
Currently aboard "Sweet Kismet", Shetland 535 / Honda 50
Experts in freshwater treatment to the marine industry.
http://www.amphibia.co.uk