Shetland 4+2 batteries

Thoughts, Ideas and General Questions
Adyb
Posts: 6
Joined: Sun Jul 17, 2016 9:23 pm

Shetland 4+2 batteries

Post by Adyb »

Hi, probably a dumb question but we don't have an owners manual.

We have two batteries, and a round red switch for selecting battery 1 or 2

Should we use both batteries, switching from time to time to keep them topped up, for starting a running the engine ?

We don't have any shore power where we are moored and don't use any other power on board as a rule....

Are the batteries both for use for starting or should only 1 or 2 be used for that and the other for on board appliances ?

Confused ?

Thanks
User avatar
DavidW
Posts: 59
Joined: Thu Jul 24, 2014 7:06 pm
Location: Wilds of the Fens

Re: Shetland 4+2 batteries

Post by DavidW »

Check what it says on the batteries..

In theory (or an ideal world) one should be a cranking battery for starting the engine and the other a leisure battery for powering any electricals you have..

The switch just enables you to switch(!) to the leisure battery when moored..so you can power lights, radio, to etc without draining the cranking battery..nothing worse than going to start the boat and hearing the dreaded flat battery clunk..

When I refurbished my Saxon, I installed a split charge system that charges the crank battery first and then tops up the leisure battery...a simple solution for peace of mind...
Shetland Saxon 013 "Wild Dream"
Deleted User 5743

Re: Shetland 4+2 batteries

Post by Deleted User 5743 »

Which relay did you use?
User avatar
DavidW
Posts: 59
Joined: Thu Jul 24, 2014 7:06 pm
Location: Wilds of the Fens

Re: Shetland 4+2 batteries

Post by DavidW »

I used a Durite 12v 140amp relay kit from an online supplier...

http://simplysplitcharge.co.uk/shop/viewitem.cgi?SCK111

Something similar to that if memory serves...

Works well although I do back it up with a solar panel to catch the odd ray of sunshine :D
Shetland Saxon 013 "Wild Dream"
Deleted User 5743

Re: Shetland 4+2 batteries

Post by Deleted User 5743 »

Thanks, something else on my to do list. Trying to find a home for two batteries in a f4 being another!
martin99
Posts: 8
Joined: Wed Oct 07, 2015 10:24 pm

Re: Shetland 4+2 batteries

Post by martin99 »

Thats good info and I would have used them but went to http://www.merlinequipment.com/markets/ ... groupid=18

With the system below I can leave both batteries switched on all the time without risk of flattening the starter battery.

Further if you fit a battery saver to either the domestic load or just say the 12volt the fridge circuit then you can leave the fridge on when the boat is unattended,possibly on shore power, and if the mains trips the fridge 12v supply will cut off before the battery is run completely flat.

Battery saver http://www.ebay.co.uk/itm/370935357422? ... EBIDX%3AIT

And got their Smartbank Lite system over a standard AVR ( automatic voltage{controlled} relay) because you can adjust the contact and disconnect voltages from the standard 13.8v connect to 12.5v. This is because I have as standard on the Family 4+2 two 110Ah batteries and one is for starting and one domestic.The starter battery is over rated for my Honda 25BF outboard.By adjusting the contact voltage down a bit I can use some of the starter battery capacity for the domestics without affecting the starting ability.Often have no shore power so being able to run a several more hours when static without starting the engine is useful.

From Merlin website:

An average engine uses just 1 or 2 amp hours to start?

Consider a large 2.2kW starter motor. This pulls 183A at 12V per hour. However, how long does a starter motor run
for? Typically just 10 seconds. So, take 183/60 = 3.05Ah per minute or 0.05Ah per second. 10 seconds running uses
0.5Ah. Multiply this by 2 to provide capacity required and you need just 1Ah. Most batteries need significant Ah
capacity to generate the Cold Cranking Amps necessary, but in most cases there are a fair few ‘spare’ Ah available. So
why carry spare Ah when auxiliary loads need as much power as they can get? SmartBank combiners allow you to
share some of this spare Ah capacity.
Sharing Ah capacity is achieved by setting the Disconnect Voltage lower and the Disconnect Time longer than normal.
We recommend setting the Disconnect Voltage at 12.5V to ensure that plenty of engine start capacity is left available.
This can mean as much as several hours extra operating time of auxiliary loads.

Merlin will sell to individual with about 20pc off list,although they have a highish carriage charge but includes insurance.Quoted prices are ex vat too.

I have no connection to them whatsoever just found them helpful and knowledgeable on the phone and prepared to deal with private buyers.

http://www.merlinequipment.com/markets/ ... groupid=18

Their Blue Sea fuse blocks are worth looking at to tidy up the shoddy factory wiring - the type 10-5026 one has pos and neg bus bars

12 Way
Positive & Negative Input
12 way Negative Busbar
Clip Over Cover
Max: 30A per way
Max: 100A per block
12/24V DC