Having read through the comments about water ingress between the hull and cabin/cockpit floor it seems to be a common problem. I recently purchased a 1982 F4 which was unfortunately full of water due to a leaking hatch, windows and the hood had blown off. Having sheeted the entire boat, baled out the water and stripped all the rotten wood and lining out I was hoping it would dry out.. The foam beneath the table support appears dry and at each of the plastic stoppers in the cockpit floor. There is no table support in the cockpit. The only sign of damp is where I have removed the two boxes at the back where there there appears to be a wooden cross piece beneath the floor. My question is How much timber is there beneath the floors and is the fact it could be saturated a problem? Does the foam that fills the space provide most of the support for the floors?
Thanks in anticipation Roger
Construction of a 1982 F4 below cockpit floor
-
Deleted User 5743
Re: Construction of a 1982 F4 below cockpit floor
As far as I'm aware the foam is only their for buoyancy, not structural support.
-
Cuttsee
- Posts: 9
- Joined: Wed Oct 05, 2016 7:45 am
Re: Construction of a 1982 F4 below cockpit floor
Thanks. The floor is therefore supported by wooden stringers with foam in between.
Apart from taking the the foam out completely and replacing the stringers is there anything else that can be done?
Most people seem to refere the problem of water ingress as a recuring one which does not boad well for any repair
I am wondering whether it is a problem I should ignore for the moment or tackle before I go any further. Roger
Apart from taking the the foam out completely and replacing the stringers is there anything else that can be done?
Most people seem to refere the problem of water ingress as a recuring one which does not boad well for any repair
I am wondering whether it is a problem I should ignore for the moment or tackle before I go any further. Roger
-
dellquay13
- Posts: 556
- Joined: Tue Mar 15, 2011 7:45 am
- Location: Pequod, F4 mk4, Milford Haven Marina
Re: Construction of a 1982 F4 below cockpit floor
Hi,
There are 'joists' under the wooden floor, 3x2 softwood if i remember right. The foam does in effect give some structural support where it has been well injected, but there will be big gaps where it didn't expand very well.
I stripped the rotten cockpit sole out of my '83 f4, and replaced with 12mm marine ply and 3x2 joists, and injecting extra foam into the gaps through drill holes before plugging them, because that is the way it was originally made, but in retrospect I wish I had glassed all sides of the joists and the underside of the floor before glassing and flowcoating the deck, to make it last better than the original factory finish.
Hope this helps,
Chris
There are 'joists' under the wooden floor, 3x2 softwood if i remember right. The foam does in effect give some structural support where it has been well injected, but there will be big gaps where it didn't expand very well.
I stripped the rotten cockpit sole out of my '83 f4, and replaced with 12mm marine ply and 3x2 joists, and injecting extra foam into the gaps through drill holes before plugging them, because that is the way it was originally made, but in retrospect I wish I had glassed all sides of the joists and the underside of the floor before glassing and flowcoating the deck, to make it last better than the original factory finish.
Hope this helps,
Chris
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
-
Cuttsee
- Posts: 9
- Joined: Wed Oct 05, 2016 7:45 am
Re: Construction of a 1982 F4 below cockpit floor
Thanks that makes sense. I had thought the floor was fibreglass as it does not appear to have plywood underneath where I have cut away the lockers at the back. I need to look at it more carefully. The floor is not dead flat and does flex in places which again made me think it was a sheet of fibreglass. The only access points are half a dozen plastic plugs about 1" diameter where I assume the foam has been injected. Am I right in thinking there is no connection beneath the floor between the cabin and the cockpit where water can move from one to the other? Roger
-
dellquay13
- Posts: 556
- Joined: Tue Mar 15, 2011 7:45 am
- Location: Pequod, F4 mk4, Milford Haven Marina
Re: Construction of a 1982 F4 below cockpit floor
Hi,
The floor will be made of either 9mm or 12mm ply with about 4-5mm of glass, mat and flow coat above. The ply readily delaminates and parts from the glass fibre and it all gets very springy when you get moisture under the floor, sometimes it gets a white slime all over the ply and it rots away.
This springiness and loss of plywood bonding might make you think that there isn't any plywood under the floor.
The moisture usually gets in from leaky windows but sometimes also from failed bonding between the hull and topsides under the rubbing strip; take the strip off and you will find the hull and topsides have just been riveted together, not glued and the sealant perishes. Eventually the rivets rust away and the two halves of the boat start to part. I replaced the rivets with stainless nuts and bolts after injecting new sealant.
Although the cockpit and cabin soles are at different levels, there is nothing to stop moisture freely moving under the full length. Tilt the boat and all the moisture will run to one end where you can get it out with the floor up, but try your best to seal any new flooring from below, and get some mould or damp rot inhibitor to slow any nasty growths once you seal back up. I discarded the plastic plugs from the foam holes and sealed the foam injection holes with lots of resin and matting.
Chris
The floor will be made of either 9mm or 12mm ply with about 4-5mm of glass, mat and flow coat above. The ply readily delaminates and parts from the glass fibre and it all gets very springy when you get moisture under the floor, sometimes it gets a white slime all over the ply and it rots away.
This springiness and loss of plywood bonding might make you think that there isn't any plywood under the floor.
The moisture usually gets in from leaky windows but sometimes also from failed bonding between the hull and topsides under the rubbing strip; take the strip off and you will find the hull and topsides have just been riveted together, not glued and the sealant perishes. Eventually the rivets rust away and the two halves of the boat start to part. I replaced the rivets with stainless nuts and bolts after injecting new sealant.
Although the cockpit and cabin soles are at different levels, there is nothing to stop moisture freely moving under the full length. Tilt the boat and all the moisture will run to one end where you can get it out with the floor up, but try your best to seal any new flooring from below, and get some mould or damp rot inhibitor to slow any nasty growths once you seal back up. I discarded the plastic plugs from the foam holes and sealed the foam injection holes with lots of resin and matting.
Chris
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
-
Cuttsee
- Posts: 9
- Joined: Wed Oct 05, 2016 7:45 am
Re: Construction of a 1982 F4 below cockpit floor
Thank you that's really helpful. It does seem there's a lot more to it than I thought but you've given me a good start. Roger
-
vreagh
- Posts: 327
- Joined: Sat Aug 02, 2014 5:46 pm
- Location: Cornwall
Re: Construction of a 1982 F4 below cockpit floor
Strand Glass gave a lecture on polyurethane foaming and the most important thing was keeping the foam under pressure so that it remained a closed cell structure and therefore waterproof. If allowed to foam without any constaint the foam will remain open celled and will absorb water. Hope this helps. Keith.
-
Stokey1964
- Posts: 164
- Joined: Sun Dec 07, 2014 1:54 pm
- Location: Stoke-on-Trent
Re: Construction of a 1982 F4 below cockpit floor
If you are going to redo the deck I wouldn't bother with foam
fill the voids between the stringers with either plastic balls or with 1 or 2litre empty pop bottles with the tops screwed on tight.
this will give you the buoyancy you want without worrying about foam getting saturated again.
there should be a pipe joining each of the compartments allowing water to run between each sections between the stringers.
make sure they are clear and put a bilge pump at the back or even an additional one just before the entrance to the cabin.
with the pop bottles, any water than does get in there will flow easier than if filled with foam and you can simply pump it out.
On my 570 there is also a pipe running between the cabin and cockpit between the n2 skins in the cabin.
Any water entering the cabin (leaky windows, between Hull and top half etc will find its way between the 2 skins and back under the cockpit floor, ready for the bilge to do its work
Simon
fill the voids between the stringers with either plastic balls or with 1 or 2litre empty pop bottles with the tops screwed on tight.
this will give you the buoyancy you want without worrying about foam getting saturated again.
there should be a pipe joining each of the compartments allowing water to run between each sections between the stringers.
make sure they are clear and put a bilge pump at the back or even an additional one just before the entrance to the cabin.
with the pop bottles, any water than does get in there will flow easier than if filled with foam and you can simply pump it out.
On my 570 there is also a pipe running between the cabin and cockpit between the n2 skins in the cabin.
Any water entering the cabin (leaky windows, between Hull and top half etc will find its way between the 2 skins and back under the cockpit floor, ready for the bilge to do its work
Simon
Shetland 570 MK 1
Yamaha 90 2006
Yamaha 90 2006
-
Cuttsee
- Posts: 9
- Joined: Wed Oct 05, 2016 7:45 am
Re: Construction of a 1982 F4 below cockpit floor
Thanks that's brilliant