535 transducer position

Thoughts, Ideas and General Questions
gtcamm
Posts: 14
Joined: Sat Jul 14, 2018 7:40 am

535 transducer position

Post by gtcamm »

Where have all you 535 owners positioned your fishfinders transducer? I'm struggling to position it to get good reception at speed. Its brand new and at first thought it was faulty so sent it back but its been checked and sent back to me so all to do with its location. Thanks
Adam
Posts: 86
Joined: Tue Oct 02, 2018 3:38 pm

Re: 535 transducer position

Post by Adam »

It has to be mounted to the right hand side of transom below water surface, not to close to the prop to avoid errors in reading.
And also it has to be good levelled horizontally.
Some transducers struggle giving good signal at higher speeds.
Disturbances can be also caused by mounting transducer to close to water line.
Shetland Family Four "Foxy Lady" , 70 hp Johnson EFI four str. You can meet me in the Poole Bay or Lyme Bay area from time to time \m/
gtcamm
Posts: 14
Joined: Sat Jul 14, 2018 7:40 am

Re: 535 transducer position

Post by gtcamm »

Have you got a 535 Adam? Any chance of a photo where yours is positioned
Adam
Posts: 86
Joined: Tue Oct 02, 2018 3:38 pm

Re: 535 transducer position

Post by Adam »

I have F4 but hull is same style and look almost the same. I will take a photo this evening. I'm planning to get rid of my transducer I have now and put newer one but it will be in exact the same place.
Shetland Family Four "Foxy Lady" , 70 hp Johnson EFI four str. You can meet me in the Poole Bay or Lyme Bay area from time to time \m/
gtcamm
Posts: 14
Joined: Sat Jul 14, 2018 7:40 am

Re: 535 transducer position

Post by gtcamm »

Thanks Adam
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: 535 transducer position

Post by dellquay13 »

Hi,

I've never had a boat or sounder that always had clear images on the fish finder at high speed, no matter where the transducer was situated. I am resigned to just knowing the depth at 20knots, the bottom hardness or individual fish arches are lost in the amount of surface clutter at high speed, and i kind of think that if I am going fast, then these finer details aren't that important.
Many things can cause the transducer to sit in fizzy water when at speed, such as pitted or rough antifouling causing a turbulent or aerated flow, not just it's position. If you can get the transducer to sit further out from the plane of the hull, it stands a better chance of being in clear water without bubbles rushing past confusing the echoes.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: 535 transducer position

Post by dellquay13 »

The F4 (and it's predecessor the 536) is a completely different smooth faced gull wing hull, compared to the 535 with it's lateral chines btw
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
gtcamm
Posts: 14
Joined: Sat Jul 14, 2018 7:40 am

Re: 535 transducer position

Post by gtcamm »

I've been out since my original post so here's a bit more info and an update.
My boat is a 535 suntrip.
The transom measures 20" so takes a longshaft?
I placed the transducer starboard mid way from the engine to the outside edge with the top of the transducer level with the bottom of the hull.
It was fine whilst stationary and also on tick over but lost reception(depth reading and picture) as soon as the revs was increased.
What I did notice is that there was a huge void in the water around the leg of the engine getting bigger the more the boat picked up speed.
I googled setting up an outboard and to get the cavitation plate level with th bottom of the hull I've had to jack the outboard up 60mm (I've had a plate fabricated over the transom so its safe)
This has decreased the size of the void a lot but not eliminated it.
I've also moved the transducer to within 3" of the starboard edge and set it 5mm lower than the bottom of the hull but its still loosing depth display and bottom picture when underway.
It's a lowrance hook 2 and the engine is a mariner 40hp 2 stroke longshaft
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: 535 transducer position

Post by dellquay13 »

Hi,

With a Lowrance skimmer transducer you should mount it about 300-400mm along from the keel, with the bracket as close to the edge as you can get, so that the skimmer stands as far out from the hull as possible, but still facing vertically down in the L-R axis. Tilting it up or down slightly can help improve reception. Be careful not to have the bracket protruding out from the edge of the transom (flush with the edge is best) as this would stir the water up passing the transducer. Don't mount it in line with any chines on the hull sides, try to get it behind a really smooth section of hull so the water passing over the transducer is as clear of turbulence and bubbles as possible.
You should be able to see the depth 90% of the time at speed, but consistently seeing bottom detail is rare. Getting 100% depth reading at speed depends on water and wave conditions as much as the boat installation.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...