Anyone with a Shetland 4+2 that can explain a few things

Thoughts, Ideas and General Questions
ShipShape
Posts: 18
Joined: Wed Dec 04, 2019 9:03 pm

Anyone with a Shetland 4+2 that can explain a few things

Post by ShipShape »

Hi All,

I bought a 2019 Shetland 4+2 in November. It had the water drained ready for winter, but I will be looking to get it ready for the new season soon and I was wondering if anyone with the same boat could explain a few things as there was no handover with the boat.

When I fill the water tank, is there anything that needs to be done to prime the hot water heater. It looks like there is a water shut off valve in the starboard cockpit storage locker. Is there anything else I need to do?

There is a bilge pump fitted with just a manual operation switch, but the pump has an automatic function. All that would be needed to convert to automatic is to fit a manual/auto switch but I can't see any way to access the pump, it looks like it is fitted under the cockpit floor. Is this correct, surely they wouldn't fit a pump that has no access for maintenance.
daveflack
Posts: 291
Joined: Fri Nov 08, 2013 6:54 pm
Location: Black Hawk "Atlast"Ullswater, now a 4+2

Re: Anyone with a Shetland 4+2 that can explain a few things

Post by daveflack »

Hi Shipshape, bilge pump,have you looked under the cockpit floor? I've seen some 4+2 with a deck cover so it hides the lift up lid. auto/man, if you can see into the space manual is fine, i would suggest auto if the boat was left long periods in dodgy waters & not visited to often. Water system, I would suggest check the tank is empty, if it's possible remove tank & flush with clean water. Follow pipework & check all connections & clean in-line filter as you go. Refit & part fill tank, (washdown area around filling cap to stop deck debri entering system),check for leaks,??!! check taps are off, check water heater drain-off tap is closed. turn on pump & open a cold tap,till air is out,close tap. If fitted,do same with cold tap in shower. Check tank water level fill as required. open the isol' valve to heater & turn on a hot tap, same as before let air come thro'. again check tank level as the water heater will take a good few litres to fill it. leave system to settle for a while then go round all taps again. Pump has an auto shut off feature so will switch off as system reaches pressure switching on/off as req'd. I tend to leave mine turned off until I actually need water. Re-check for leaks & hopefully it will all happen quicker than it takes to read this. cheers Magic flack.
ShipShape
Posts: 18
Joined: Wed Dec 04, 2019 9:03 pm

Re: Anyone with a Shetland 4+2 that can explain a few things

Post by ShipShape »

Thanks for the reply, that all makes sense. My last boat was very basic with no hot water, heating, etc., so this is all new to me.

Regarding the bilge pump, I have looked in the hatch under the cockpit floor and it's definitely not in there, all that is in there is the waste holding tank. I believe the pump is in the space below the floor of this space but I can't see anyway to access it as there is no opening or hatch into the space that I can see. I can't believe they would fit an electric pump into a space that has no access. There is also no way to see if there is water in the bilges. Unless there is an access point under the waste tank (which would be awkward to move), I am stumped.

Thanks Alan
daveflack
Posts: 291
Joined: Fri Nov 08, 2013 6:54 pm
Location: Black Hawk "Atlast"Ullswater, now a 4+2

Re: Anyone with a Shetland 4+2 that can explain a few things

Post by daveflack »

Hello again, if the waste tank in that space is under the step down into the cabin, then that is a relatively flat solid section not open to inspection anyway, sorry I don't think I can be anymore help cheers
daveflack
Posts: 291
Joined: Fri Nov 08, 2013 6:54 pm
Location: Black Hawk "Atlast"Ullswater, now a 4+2

Re: Anyone with a Shetland 4+2 that can explain a few things

Post by daveflack »

Never thought before,have traced back from the 0verboard discharge plpe for the bulge pump to see where it goes through the void & bulkhead? I ask coz I think there is a void under the bathroom floor & under the table. If memory is right there is also a shallow void under main cabin floor, so as to give a flat surface, it's possible it's going to be under the cabin entrance step, good luck
daveflack
Posts: 291
Joined: Fri Nov 08, 2013 6:54 pm
Location: Black Hawk "Atlast"Ullswater, now a 4+2

Re: Anyone with a Shetland 4+2 that can explain a few things

Post by daveflack »

If you turn the pump on can you hear it?
Gillpap
Posts: 2
Joined: Tue Apr 09, 2019 2:19 pm

Re: Anyone with a Shetland 4+2 that can explain a few things

Post by Gillpap »

My 4 + 2 hasn’t got a bulge pump and I’ve been advised doesn’t need one ?
Also new to this and have lots of questions!
Does anyone know someone who can do various odd jobs on our boat? We are in Roydon.
Gill
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Anyone with a Shetland 4+2 that can explain a few things

Post by Clive »

Mine doesn't have a bilge pump and also came with no real handover. I agree with Dave, have a listen when you switch it on. At the risk of sounding like a complete idiot(!) if the hull of the boat is sound, where does water get in that you can't see? The cavities under the heads and cabin floor would surely only collect water if there was a) a hole in the hull, or b) there was a leak elsewhere that was draining down through the boat, which you would certainly see. The cockpit area on mine is easily accessible under the seats and the floor locker. When I collected the boat it had a new canopy fitted. Whilst the old one was off we had a very we week. At home looking over the boat, both lockers under the seats had a few litres of water. The floor locker space (used for engine if you have an inboard) was bone dry. I cleared out the water using a vacuum pump and it's been bone dry since. I don't feel any need for a bilge pump, or am I missing something?

And Hi Gill, welcome! I have a 1989 4+2 which I bought late last summer and I love it. A lot of room for size of boat and very comfy cruising. Can't help with who might work on the boat - I just Google! There's lots of boat people in your part. I'm in Guildford. Been the River Wey so far and will get on the Thames this year. I am posting about issues that need fixing on another post so I don't hijack this thread.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
aggalletley
Posts: 63
Joined: Fri Feb 24, 2012 4:44 pm

Re: Anyone with a Shetland 4+2 that can explain a few things

Post by aggalletley »

Good idea to try listening for the pump when switched on. Or try to follow the wiring from the switch to the pump. Bilge pumps are not fitted as standard to 4 + 2s. My boat had a small leak which was only a slight trickle but over a period of two weeks made the carpet in the cabin wet. Cause of the leak was under the rubbing strake ( The rubber buffer which runs all round the boat ) Once you manage to get part of this off (a swine of a job....even harder getting it back on) where the leak is you will see where the top of the boat is bolted to the bottom half of the boat. On mine there were gaps where the two halves meet and I simply sealed the gaps with mastic.
Sometimes there are switches on the boat which are not operational. Check there is current flow when the bilge pump is switched on. My boat has a windscreen wiper switch but no windscreen wiper !!!! Wiring is still there but taped at the end where motor should have been.

Enjoy your boat, I have had my 4 + 2 for nine years and still love it !!! Know her inside out by now.
Good luck
Andrew
ShipShape
Posts: 18
Joined: Wed Dec 04, 2019 9:03 pm

Re: Anyone with a Shetland 4+2 that can explain a few things

Post by ShipShape »

Hi all

Thanks for all the replies. Couple of things:

1. The bilge pump was definitely fitted as standard by Shetland when the boat was built 12 months ago
2. I can't believe they would fit a serviceable item in an inaccessible place so I must be able to get to it
3. I think it must be under the engine locker floor, the side lockers under the seats are much deeper than the space where the inboard would go so there must be a void under there.

I will keep looking, I am sure at some point I will find it