Sheltie 535

Thoughts, Ideas and General Questions
Davie1
Posts: 18
Joined: Sat Apr 18, 2020 3:34 pm

Sheltie 535

Post by Davie1 »

Hi all, just starting a project sheltie 535, been lying in a field for about 7 to 8 years, got her all power washed and cleaned up. Luckily I have a 2 post car lift so got her onto the lift and finished scraping the bottom of about 5 coats of antifoul. So far found one really bad repair on the bottom about one foot forward of the transom and a hole half way along the port side right on the corner where the side meets the bottom of the hull about a kidney bean size once I dug out the filler (scary). Port side inside is spongy to walk on so going to cut top of and get better access to second hole and clean out any crap, wood or foam that is there. Amazingly the yam 40 2 stroke fired up straight away but will probably replace with an etec when boat is finished which will take while, any advice most welcome, by the way repairs will be done with epoxy so no shrinkage and peeling repairs.
David
Ps have test drilled tha transom, stringers and starboard flooring and all dry
Davie1
Posts: 18
Joined: Sat Apr 18, 2020 3:34 pm

Re: Sheltie 535

Post by Davie1 »

20200325_111901.jpg
20200411_135853.jpg
20200411_135907.jpg
20200325_111851.jpg
20200325_151209.jpg
20200325_151209.jpg
20200421_120146.jpg
You do not have the required permissions to view the files attached to this post.
535Mustard
Posts: 177
Joined: Sun Dec 29, 2019 11:07 am

Re: Sheltie 535

Post by 535Mustard »

Looks great.
With a bit of work she will be lovely.

Tom
Davie1
Posts: 18
Joined: Sat Apr 18, 2020 3:34 pm

Re: Sheltie 535

Post by Davie1 »

20200422_112424.jpg
20200422_112408.jpg
20200422_112404.jpg
You do not have the required permissions to view the files attached to this post.
Davie1
Posts: 18
Joined: Sat Apr 18, 2020 3:34 pm

Re: Sheltie 535

Post by Davie1 »

Shows what can be achieved with a scraper and wire wool, next is to attack the inside.
Davie1
Posts: 18
Joined: Sat Apr 18, 2020 3:34 pm

Re: Sheltie 535

Post by Davie1 »

That's the top of the port side deck off and all the soaking rotten wood cleaned out. That should now be the hull sound and ready to crack on with rest of it.
Davie1
Posts: 18
Joined: Sat Apr 18, 2020 3:34 pm

Re: Sheltie 535

Post by Davie1 »

Used plastic closed cell boarding that's used for guttering facia and was the perfect thickness in 2" width strips instead of ply, silicone these in place and used the cleaned up fibre glass that was the old deck, silicone in place and fiberglass matting twice over the whole area. Seems to be a nice solid job, I know this is not standard but should be a lot better than the rotten ply that was there. Now that the deck is sealed and the hole repaired that hopefully is the hull sound.
Davie1
Posts: 18
Joined: Sat Apr 18, 2020 3:34 pm

Re: Sheltie 535

Post by Davie1 »

20200425_110035.jpg
You do not have the required permissions to view the files attached to this post.
Davie1
Posts: 18
Joined: Sat Apr 18, 2020 3:34 pm

Re: Sheltie 535

Post by Davie1 »

So boat obviously a sheltie although the engine well is much smaller (shorter) than any other sheltie I have seen, are they all classed as 535.
Adam
Posts: 86
Joined: Tue Oct 02, 2018 3:38 pm

Re: Sheltie 535

Post by Adam »

I love when people bring to life an old boats but sometimes it is worth to calculate the time and money put into the project and very often we starting to realise that the best solution is to buy sea worthy boat rather than fix the old one.

Good luck with your project mate and I look forward to see how it goes!
Shetland Family Four "Foxy Lady" , 70 hp Johnson EFI four str. You can meet me in the Poole Bay or Lyme Bay area from time to time \m/