Hi everyone I was just wondering if anyone can advise me on fitting an electric bilge pump on my black hawk.
I’m not sure where will be the best location to fit it either under the floor in the cockpit or under the engine bay right at the back.
I’m sure there’s quite a bit of water in between the gaps if the hull around the cockpit area but I can’t find a drain hole anywhere and so I was wondering if there’s a good location to drill a small hole to get all the water out.
Any advice will be greatly appreciated
Bilge pump
-
THEDAMMAN
- Posts: 27
- Joined: Mon Jul 25, 2011 6:28 pm
- Location: KIELDER NORTHUMBERLAND
-
dellquay13
- Posts: 556
- Joined: Tue Mar 15, 2011 7:45 am
- Location: Pequod, F4 mk4, Milford Haven Marina
Re: Bilge pump
Hi,
The cockpit sole should be airtight, apart from a small hole as low as possible draining any water into the sump under the engine splashwell. This is to keep as a big a 'bubble' of bouyancy as possible in case of swamping. If it isn't airtight on top, then air can get out letting water in, and your bouyancy is gone, unless you have good foam under the sole.
Fit your bulge pump into the sump, and make sure nothing can stop the float switch lifting, if it is separate from the pump. Glue something over it, like an upturned Tupperware box with vent holes top and bottom to let any water in freely.
Chris
The cockpit sole should be airtight, apart from a small hole as low as possible draining any water into the sump under the engine splashwell. This is to keep as a big a 'bubble' of bouyancy as possible in case of swamping. If it isn't airtight on top, then air can get out letting water in, and your bouyancy is gone, unless you have good foam under the sole.
Fit your bulge pump into the sump, and make sure nothing can stop the float switch lifting, if it is separate from the pump. Glue something over it, like an upturned Tupperware box with vent holes top and bottom to let any water in freely.
Chris
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
-
THEDAMMAN
- Posts: 27
- Joined: Mon Jul 25, 2011 6:28 pm
- Location: KIELDER NORTHUMBERLAND
Re: Bilge pump
Thanks for that chris but there's no hole in that sump area there's a drain hole as you mentioned that goes out of the back of the sump exiting under the engine to the outside this is underwater when in the water but there's nothing I can find to let any water that's between the hull where the foam is out so I'm thinking that I may have to drill a hole in the sump on the inner wall that forms the cockpit floor,that way the water can drain into this sump at the back where you suggested fitting the bilge pump.
Should there be a drain hole here ?
Should there be a drain hole here ?
-
dellquay13
- Posts: 556
- Joined: Tue Mar 15, 2011 7:45 am
- Location: Pequod, F4 mk4, Milford Haven Marina
Re: Bilge pump
Hi,
There isn't usually a drain for the foam under the sole, which is why so many get waterlogged over the years, but if you really want one, drill it low down being aware of how close you are getting to the keel. Personally, I would aim for about an inch up, I could live with an inch of water, but not a hole through the bottom.
There isn't usually a drain for the foam under the sole, which is why so many get waterlogged over the years, but if you really want one, drill it low down being aware of how close you are getting to the keel. Personally, I would aim for about an inch up, I could live with an inch of water, but not a hole through the bottom.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
-
THEDAMMAN
- Posts: 27
- Joined: Mon Jul 25, 2011 6:28 pm
- Location: KIELDER NORTHUMBERLAND
Re: Bilge pump
That would explain why I can’t find a drain hole.
I think that sounds like the best idea,I will drill a hole there next to the sump under the engine bay and fit a pump also.
I know that there’s water inside as it’s been standing a while now so I will follow your advice and get it drained out that way,I just wasn’t sure if the existing hole that’s there opened up a gap between the hull when the bolt was removed to let the water drain out.
Thanks for your help.
I think that sounds like the best idea,I will drill a hole there next to the sump under the engine bay and fit a pump also.
I know that there’s water inside as it’s been standing a while now so I will follow your advice and get it drained out that way,I just wasn’t sure if the existing hole that’s there opened up a gap between the hull when the bolt was removed to let the water drain out.
Thanks for your help.