Hi
I have purchased a couple of new seat Pedestals (for my Family 4 1990), that adjust up/down and have a small adjustment to move nearer or further away from helm etc.
Has anyone got advise as to how to fit them to the deck? I can not access underneath the floor/deck in the cockpit to use the nut and bolt system. Will decent stainless steel screws hold the seats securely? Before I purchased the boat the floors and upholstery had been renewed and a full cockpit deck rubber cover has been stuck to the deck/floor area. I am not sure how thick the floor is, but assume it will be at least half an inch/13mm thick. I also assume that under the flooring will be the foam buoyancy material.
Looking for advice and ideas.
Thanks, Dave
Fitting Pedestal seats in a Family 4
-
dellquay13
- Posts: 556
- Joined: Tue Mar 15, 2011 7:45 am
- Location: Pequod, F4 mk4, Milford Haven Marina
Re: Fitting Pedestal seats in a Family 4
Hi,
My mid 80s F4 has a 12mm ply cockpit sole with 2"x 1 3/4" pine timbers screwed to the underside for stiffening. The timbers sit on the hull at the gull wing arches. The foam was then injected underneath through 1" holes every 18" or so, plugged with white plastic caps. If the sole on yours has been replaced then most people lay thicker ply. You may want to fit an oversized ply pad to the sole before screwing the pedestal down to the pad. Remember over the gull wing arch in the hull you have only about 1 3/4" between the ply and the hull.
A pedestal mounted seat will put a lot of strain on the fixings at the bottom, as it will act as a lever amplifying the movements of your body weight as you sway with the boats motion, which is probably why Shetland always fitted the side mounted seats supported on the ladder rack with no tearing forces on the ply.
If you are purely inland and at slow speeds it probably won't be too much of a problem, if you are coastal or at speed then I don't think it will stand up to the strain.
Chris
My mid 80s F4 has a 12mm ply cockpit sole with 2"x 1 3/4" pine timbers screwed to the underside for stiffening. The timbers sit on the hull at the gull wing arches. The foam was then injected underneath through 1" holes every 18" or so, plugged with white plastic caps. If the sole on yours has been replaced then most people lay thicker ply. You may want to fit an oversized ply pad to the sole before screwing the pedestal down to the pad. Remember over the gull wing arch in the hull you have only about 1 3/4" between the ply and the hull.
A pedestal mounted seat will put a lot of strain on the fixings at the bottom, as it will act as a lever amplifying the movements of your body weight as you sway with the boats motion, which is probably why Shetland always fitted the side mounted seats supported on the ladder rack with no tearing forces on the ply.
If you are purely inland and at slow speeds it probably won't be too much of a problem, if you are coastal or at speed then I don't think it will stand up to the strain.
Chris
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
-
jetting1
- Posts: 3
- Joined: Sat Aug 22, 2020 9:54 am
Re: Fitting Pedestal seats in a Family 4
Thanks for your info. I do have a 60hp 2 stroke on the back so the boat will hit 30mph at so on the local lake. I will look into screwing a separate layer of marine ply to the deck first to help spread the load. Just so fed up with the seating as it is as takes up room and looks pretty poor. Plus the 'ladder' frame etc is not 100% stable and does not seem to be very strong. I have taken one of the seats off the frame and will take out the ladder frame and bench seat so as I can see exactly what has been done in the past. Because the flooring has a good quality rubber 'carpet' fitted I am somewhat reluctant to rip it up. So I guess I will use waterproof mastic to bed the separate layer of ply to the rubber and screw it down, then mount the pedestal onto it with stainless screws. Obviously it looks like I can only use screws of 2" or less. So will see what happens tomorrow, weather permitting.
-
dellquay13
- Posts: 556
- Joined: Tue Mar 15, 2011 7:45 am
- Location: Pequod, F4 mk4, Milford Haven Marina
Re: Fitting Pedestal seats in a Family 4
You can use longer screws in the sections where the hull is deeper, towards the keel and the outside edge, just be aware of the arch of the gull wing. Which to be realistic is pretty much directly under where the seat is. If the boat is on the trailer, and not afloat, then it is a lot easier to judge where the arch is in relation to the pedestal.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
-
jetting1
- Posts: 3
- Joined: Sat Aug 22, 2020 9:54 am
Re: Fitting Pedestal seats in a Family 4
Hi, Thanks again for your info. The boat is on it's trailer so will be easier to see the lines of the hull etc, and indeed be solid to carry out the works.
The other issue I have with the original seats is the height of them, too high. I guess this is useful if on canals/rivers with slow speed restrictions etc, but anything over 20 mph it is not so good.
Ha! miserable weather has put paid to works on boat today, tomorrow promises to be good.
The other issue I have with the original seats is the height of them, too high. I guess this is useful if on canals/rivers with slow speed restrictions etc, but anything over 20 mph it is not so good.
Ha! miserable weather has put paid to works on boat today, tomorrow promises to be good.
-
BryanMcCrae
- Posts: 6
- Joined: Mon Apr 21, 2014 4:28 pm
Re: Fitting Pedestal seats in a Family 4
Hi, I'm also thinking of fitting Pedestal seats to a Family 4 ( a plus 2 in my case).
How did you get on with doing it ? Any particular seat recommendations, snags, hints or photos would be much appreciated!
Thanks,
Bryan
How did you get on with doing it ? Any particular seat recommendations, snags, hints or photos would be much appreciated!
Thanks,
Bryan