Family Four restoration advice needed.

Thoughts, Ideas and General Questions
KenGreenaway
Posts: 11
Joined: Tue Apr 20, 2021 1:34 pm

Family Four restoration advice needed.

Post by KenGreenaway »

I'm new to the association and just realised I posted a topic in the wrong forum so here goes again. I'm restoring a Family Four that I recently bought and need some advice. First of all I'd like to know the age of my boat as all the insurance companies ask this. The registration is 9226.
The biggest part of the restoration is replacing the floor of the boat. The wood is very damp and simply putting a sheet of wood over it doesn't seem a good idea to me. I've started to cut out the old floor which I will replace with 12mm marine ply. Should I coat the board with epoxy on both sides? Do I need to put layers of fibreglass sheeting on the upper surface if I intend covering it with waterproof boat decking sheets?
The original foam is also very damp and disintegrating in places. Is it really necessary?
If I find that the crossmembers are suffering from damp do I need to replace them with hardwood or is treated softwood sufficient?
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Family Four restoration advice needed.

Post by dellquay13 »

I treated both sides of the floor, and treated the softwood bearers that i replaced. I kept the foam, as it actually gives the floor a lot of it's strength, even when a bit crumbly.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Family Four restoration advice needed.

Post by Clive »

I agree - the foam will also stop the boat sinking god forbid that situation was ever to occur. I've read elsewhere that foam is a pain and tends to end up wet. People use plastic bottles, balls from play pits and ping pong balls instead to give buoyancy. If the boat is sealed properly foam would be my choice.
Cheers, Clive
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Family Four restoration advice needed.

Post by dellquay13 »

Serial no. 9226 was approx 1980-81 according to the F4 page in the specs section.
Many insurance companies want to see surveys for older boats, so you may have to search further for a provider of cover without a survey.

Joining the forum (£5 one off fee) allows you access to all the sections, including boat specs and full privileges with pictures
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
KenGreenaway
Posts: 11
Joined: Tue Apr 20, 2021 1:34 pm

Re: Family Four restoration advice needed.

Post by KenGreenaway »

I have removed the foam as it was very wet and the cross members are rotting. I think I should increase the number of cross beams to provide more support to the floor but am not keen on injecting foam again. I'll create some hatches to give access to the underfloor area and keep adding plastic bottles for added buoyancy. When I removed the foam there were differing thicknesses of old epoxy attached. Should I layer the inner hull with fiberglass sheets and resin or is that not necessary?
The cross member at the stern is a big lump of wood 8 inches across by 4 inches deep. That's a difficult size to get a hold of. Are there alternatives to it?
Thanks for the help so far.
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Family Four restoration advice needed.

Post by Clive »

Not an expert on this model but you could clamp and glue 4x2 pieces to create the thickness. I use a phenomenal glue called called Lumberjack wood adhesive
https://www.toolstation.com/5-minute-po ... gel/p78519?
If you go that route I’d use 326 stainless bolts for additional strength. Can you post some pics? Cost £5 to register and see/post pics- well worth it.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
KenGreenaway
Posts: 11
Joined: Tue Apr 20, 2021 1:34 pm

Re: Family Four restoration advice needed.

Post by KenGreenaway »

Image[/img]Paid my £5 but don't seem able to attach photos.
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Family Four restoration advice needed.

Post by Clive »

That's not the best way - under the post are two tabs. Use "Attachments" to add files. Only they post in reverse order, so if posting a sequence, load the last pic first (unless you do them one by one). You can add comments if you like as I have. Hope this helps. It may take a bit of time for you to get full access.
You do not have the required permissions to view the files attached to this post.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Family Four restoration advice needed.

Post by dellquay13 »

Having your membership upgraded is done manually by Sue admin, it isn't automated so can take a day or two to do. When your user name turns from purple to blue, then your full membership has been processed.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
KenGreenaway
Posts: 11
Joined: Tue Apr 20, 2021 1:34 pm

Re: Family Four restoration advice needed.

Post by KenGreenaway »

I've attached three photos showing the disaster area. Today I almost finished removing the dreaded foam and should soon be at the stage of placing new crossbeams and flooring. Should I reinforce the area for the helmsman's pillar seat by putting an extra layer of ply below that area of the floor or is it just as good to put it on top of the wood?
All new wood will be "painted" with epoxy resin. Does it need fibreglass matting as well?
I don't see any point in trying to trim the old fibreglass floor flush with the sides of the boat. If I get the new ply close to it I can blend them together with new epoxy.
You do not have the required permissions to view the files attached to this post.