Hi all.
I’m designing my inboard fuel tank for my 4+2 and on the boat today found that the primer bulb (new last season) is hard - they only seem to last for one year, so I’m wondering about using an electric primer. Does anyone use one? Lots of fuel pumps but that not what I want. It would be switched.
I was reading on the BSS site about inboard fuel tanks and as my BSC is due in June, thought I’d run aluminium or copper fuel lines from the tank to the transom. I’d add the pump to that and put a filter in the line too.
Planning a 50L stainless steel tank. I think I’ll run the filler and vent pipes to port with a sender unit and fuel gauge at the helm. I’ve been pondering this since I got the boat so it’s an exciting project and one that will make the boat much safer.
New inboard fuel tank
-
Clive
- Posts: 548
- Joined: Sun Jun 23, 2019 8:41 am
New inboard fuel tank
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
-
vreagh
- Posts: 327
- Joined: Sat Aug 02, 2014 5:46 pm
- Location: Cornwall
Re: New inboard fuel tank
My inboard 535 has a engine driven AC mechanical pump which works fine. Though, if I leave the boat for a week, the engine has to spin a fair while to pull the petrol back up. I used a cheap ebay electric fuel pump in the line with a separate switch as a primer until it stops pumping, then switch off. So, the engine is full primed before starting. The engine happily pulls fuel through the idle pump. The pump casing is all metal. The only slight disadvantage is the pump is noisy when operating.
-
vreagh
- Posts: 327
- Joined: Sat Aug 02, 2014 5:46 pm
- Location: Cornwall
Re: New inboard fuel tank
Found the ad for the pump.
You do not have the required permissions to view the files attached to this post.
-
Clive
- Posts: 548
- Joined: Sun Jun 23, 2019 8:41 am
Re: New inboard fuel tank
Hi vreah, thanks for this. There are loads of this type out there, good to hear they work! Isn't the noise it makes a good thing so you can hear when it's done it's job and primed - ie stops pumping? Other question is what switch do you use? I was thinking of putting a push button on the helm for ease, but it wouldn't need to stay on so something horn button style that is sprung. Struggling to find one of those.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
-
Clive
- Posts: 548
- Joined: Sun Jun 23, 2019 8:41 am
Re: New inboard fuel tank
Vreah - found push button switches which will do the job, so unless you have a different solution...
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
-
vreagh
- Posts: 327
- Joined: Sat Aug 02, 2014 5:46 pm
- Location: Cornwall
Re: New inboard fuel tank
I would think a push button is a good idea. I find it rarely needs to pump for more than 10 seconds often less. Yes, the noise lets you know when its fully primed.
-
vreagh
- Posts: 327
- Joined: Sat Aug 02, 2014 5:46 pm
- Location: Cornwall
Re: New inboard fuel tank
Looking at push buttons, most aren't capable of carrying spikes of heavy current and would need a relay to be reliable . Below is a momentary toggle switch with the option of a waterproof cover. No relay would be necessary.
You do not have the required permissions to view the files attached to this post.
-
blebrocq
- Posts: 108
- Joined: Thu Oct 20, 2022 11:24 am
Re: New inboard fuel tank
Hi Clive.
For what it's worth my 4+2 (new last year) has a plastic inboard tank, mounted sideways on under the cabin doors, with flexible hoses connecting it to the engine. there is a fuel cock near the tank, & a rubber primer outside near the engine. filler pipe connects the port side of the tank to the the port side gunnal adjacent to the engine controls, there is also a tank vent pipe which runs to a fitting approx 8" above the filler filling. You can just see it in this poor photo ! It did come with a contents gauge on the dash.
Bob
For what it's worth my 4+2 (new last year) has a plastic inboard tank, mounted sideways on under the cabin doors, with flexible hoses connecting it to the engine. there is a fuel cock near the tank, & a rubber primer outside near the engine. filler pipe connects the port side of the tank to the the port side gunnal adjacent to the engine controls, there is also a tank vent pipe which runs to a fitting approx 8" above the filler filling. You can just see it in this poor photo ! It did come with a contents gauge on the dash.
Bob
You do not have the required permissions to view the files attached to this post.
-
Clive
- Posts: 548
- Joined: Sun Jun 23, 2019 8:41 am
Re: New inboard fuel tank
Thanks Bob, that's where I concluded would be the best route for the filler and vent pipe. Do you by any chance have and pictures of the routing? I'm really done with primer bulbs. I keep buying them and over winter they get so hard as to be barely usable, hence my thoughts on having a small pump instead. The bulb perished outside so it is currently close to the tanks in the central void but this new one is hard again. I drain out the whole system before winter and I make sure I have a petrol not diesel bulb.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
-
daveflack
- Posts: 291
- Joined: Fri Nov 08, 2013 6:54 pm
- Location: Black Hawk "Atlast"Ullswater, now a 4+2
Re: New inboard fuel tank
Hi Clive, this my tank install & pipe layout.
You do not have the required permissions to view the files attached to this post.