Hi All,
I am a new member to the Shetland owners forum so this is my first post, hopefully I have posted in the correct category, if not I apologies.
I have just purchased a Shetland 535 (not sure on the year) the boat looks sound but is in need of various repairs which I intend to carryout this year I am in no rush to get into the water straight away and I am looking at this as a project to work on over the coming year. The previous owner bought the boat as a project but once bought it sat on its trailer for 18 months with nothing getting done.
However I am in need of some advice if possible, so I thought that this would be a great place to start. Please excuse my ignorance if I ask what would be considered a foolish question but I feel that it better to get advice first, even if it make me look stupid (that won't be hard!).
Can anyone offer help on the following please.
The boat hull does not appear to have a gelcoat it looks like it has been painted which is now beginning to flake in various areas, I can’t see anything resembling spider cracks or any shine or gloss effect material.
I want to rubdown the entire hull, but not sure what I do after this, should I put a marine primer on then paint with marine paint, then put a gel coat on top and buff up, or do I rubdown then put on a colour gel coat with no need to paint. At what stage would I put an antifoul coat on.
I don’t mind the amount of work that I will need to do no matter how much, but need some guidance on what method I should use and would be grateful for any advice available.
My current plan is to start on the hull and complete then work my way up the boat once the hull is done I need to look at the rest of the boat.
A quick summary of my intentions are:
Remove all fixture and fittings
Remove all current electrical wiring
Put a new marine ply floor in place (currently no floor)
Rubdown boat interior
Prime and repaint boat interior (with new floor removed)
Insert floor
Replace all wiring with marine grade wire
Replace fittings with marine grade fittings
Hopefully you will have manage to stop laughing, so any help would be greatly appreciated.
(If it helps I can get and post photos)
Best regards and thanks in advance.
Hi all Newbie in need of help repairing
-
Glimmers
- Posts: 7
- Joined: Mon May 28, 2012 9:34 pm
- Location: Cumbria and Caithness (not at the same time - work related)
-
admin
- Site Admin
- Posts: 862
- Joined: Sat Feb 19, 2011 3:00 pm
- Location: "Phonix" , Tuckton Basin, Christchurch
Re: Hi all Newbie in need of help repairing
Hello and welcome.
Firstly at somepoint we have all asked what seems to be a stupid question. There is no such thing. We are all experienced here, some more than others and within a short length of time you will be dealing out the advice like a pro. There is a wealth of knowledge here, do not be afraid to ask.
we love projects so post some pics and we will see what we can do to help
Sue - ADMIN
Firstly at somepoint we have all asked what seems to be a stupid question. There is no such thing. We are all experienced here, some more than others and within a short length of time you will be dealing out the advice like a pro. There is a wealth of knowledge here, do not be afraid to ask.
we love projects so post some pics and we will see what we can do to help
Sue - ADMIN
There is NOTHING--absolutely nothing--half so much worth doing as simply messing about in boats.
Kenneth Grahame
Kenneth Grahame
-
Glimmers
- Posts: 7
- Joined: Mon May 28, 2012 9:34 pm
- Location: Cumbria and Caithness (not at the same time - work related)
Re: Hi all Newbie in need of help repairing
Hi admin,
Thanks,
I have uploaded some photos to a web site i have, tried to use the image tag when posting a reply but the preview only shows the html code, do I send the image URL links to you or the html code or even just the photos.
Regards
George
Thanks,
I have uploaded some photos to a web site i have, tried to use the image tag when posting a reply but the preview only shows the html code, do I send the image URL links to you or the html code or even just the photos.
Regards
George
-
admin
- Site Admin
- Posts: 862
- Joined: Sat Feb 19, 2011 3:00 pm
- Location: "Phonix" , Tuckton Basin, Christchurch
Re: Hi all Newbie in need of help repairing
Reduce them to 640 x 480
you need to set them either in the IMG (above in a new message) tags , a ULR in the ULR tags or go to the bottom of the new post and use the UPLOAD ATTACHMENT TAB
Any problems, send them to me and I will post from my end
[email protected]
you need to set them either in the IMG (above in a new message) tags , a ULR in the ULR tags or go to the bottom of the new post and use the UPLOAD ATTACHMENT TAB
Any problems, send them to me and I will post from my end
[email protected]
There is NOTHING--absolutely nothing--half so much worth doing as simply messing about in boats.
Kenneth Grahame
Kenneth Grahame
-
Glimmers
- Posts: 7
- Joined: Mon May 28, 2012 9:34 pm
- Location: Cumbria and Caithness (not at the same time - work related)
Re: Hi all Newbie in need of help repairing
Thanks Admin,
Hope the sizes are ok





Hope the sizes are ok





-
goldenfleecer
- Posts: 11
- Joined: Sun Mar 25, 2012 7:44 pm
Re: Hi all Newbie in need of help repairing
hi it sounds like you need to rub down your boat then paint it you should re search some paints. there are two types single pack and two pack you can only apply 2 pack to the gel coat ( cannot be applied over single pack paint). alot of people recomend using flow coat . your boat will alredy have a gel coat this underneath the paint you gonna sand off. good luck and remember the paint paint job will only look good if you properly prep the boat
-
Glimmers
- Posts: 7
- Joined: Mon May 28, 2012 9:34 pm
- Location: Cumbria and Caithness (not at the same time - work related)
Re: Hi all Newbie in need of help repairing
Thanks Goldenfleecer, I will start the rub down now while researching the paint side of things.
George
George
-
Glimmers
- Posts: 7
- Joined: Mon May 28, 2012 9:34 pm
- Location: Cumbria and Caithness (not at the same time - work related)
Re: Hi all Newbie in need of help repairing
Me again,
Now getting myself confused, but here goes, once the hull is rub down (now started) and I have researched the paint, do I then put an anti foul paint on top of the paint I have put on or should I be looking for the paint I put on once rubbed down being an anti foul paint. (The boat will be berthed in a seawater harbor and used in coastal waters)
George
Now getting myself confused, but here goes, once the hull is rub down (now started) and I have researched the paint, do I then put an anti foul paint on top of the paint I have put on or should I be looking for the paint I put on once rubbed down being an anti foul paint. (The boat will be berthed in a seawater harbor and used in coastal waters)
George
-
daveinglasgow
- Posts: 680
- Joined: Tue Mar 15, 2011 9:04 am
- Location: Dave Ashton, Shetland 610 Glasgow & Loch lomond
Re: Hi all Newbie in need of help repairing
Hi
rub down, prime ( depending on paint used), paint, anti foul or if you hate that job spend a bit more and copper coat as this will last 10+ years.
oh and giving it 2 layers of paint never hurts as some idiot will bang into your boat before you can say thank god I bought a shetland.
Dave
rub down, prime ( depending on paint used), paint, anti foul or if you hate that job spend a bit more and copper coat as this will last 10+ years.
oh and giving it 2 layers of paint never hurts as some idiot will bang into your boat before you can say thank god I bought a shetland.
Dave
http://www.ashtonmarineservices.co.uk, Brokergae, Trailers, advice, boat transportation 0759 563 8185
https://www.facebook.com/ashtonmarineservices
https://www.facebook.com/ashtonmarineservices
-
Glimmers
- Posts: 7
- Joined: Mon May 28, 2012 9:34 pm
- Location: Cumbria and Caithness (not at the same time - work related)
Re: Hi all Newbie in need of help repairing
Dave,
Thanks for the info much appreciated, looks like a busy bank holiday weekend.
George
Thanks for the info much appreciated, looks like a busy bank holiday weekend.
George