Family Four restoration advice needed.

Thoughts, Ideas and General Questions
Clive
Posts: 548
Joined: Sun Jun 23, 2019 8:41 am

Re: Family Four restoration advice needed.

Post by Clive »

Fully fledged member now!
I’m sure Dellquay13 will know better than me but I wouldn’t have bthought extra ply would be needed under the helm seat. You may want to add an extra strut or a noggin for strength, specially I’d your not using foam.
I would definitely think about the advantages of removing all the old floor up to the hull - where are the leaks that caused the damage? Almost certainly on that join. All it needs is a hairline crack you might not see and water will get in again. Is glassing over old damaged glass ok? I don’t know but you’re in so far I’d get it fully sorted - not much more work in the scheme of things. Sure I’ll be corrected if that’s not best advice. Good luck.
4+2 (1988) 35hp Honda outboard, currently in a field outside Horsham.
vreagh
Posts: 327
Joined: Sat Aug 02, 2014 5:46 pm
Location: Cornwall

Re: Family Four restoration advice needed.

Post by vreagh »

It's not a good idea to bring plywood too close to the hull as it can cause a hard spot. Better to leave 1/2 inch or so, then glass it in. Hard spots spoil the natural flex and can cause crazing of the gel coat or even de-lamination.
vreagh
Posts: 327
Joined: Sat Aug 02, 2014 5:46 pm
Location: Cornwall

Re: Family Four restoration advice needed.

Post by vreagh »

It's not a good idea to bring plywood too close to the hull as it can cause a hard spot. Better to leave 1/2 inch or so, then glass it in. Hard spots spoil the natural flex and can cause crazing of the gel coat or even de-lamination.
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Family Four restoration advice needed.

Post by dellquay13 »

The original ply floor on mine was right up to the hull, so i replaced it the same. The floor comes up to the hull in particularly rigid zones anyway, just above the gullwings, and i have never seen any problem on mine since replacing the cockpit sole over 10 years ago.
I used a couple of layers of woven mat over the boards. The floor originally had chopped strands so i thought it best to glass some fibres in again for strength.
I didn't add any extra stiffening under the helm, as I still use the original seat on the side mount and ladder rack, so there is little localised pressure on the floor. Some people use pillar seats, but I think they are a really bad idea on a sea going boat, 12stone wildly rocking about on the end of a 1m lever must really stress the floor.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
KenGreenaway
Posts: 11
Joined: Tue Apr 20, 2021 1:34 pm

Re: Family Four restoration advice needed.

Post by KenGreenaway »

I've been warned about possible twisting or flexing of the hull when i remove the last of the cross-members. At the moment it would seem not to pose a problem as the central bulkhead and the large beam across the stern must be holding the shape. If I install the first half of the floor (which would cover four feet from the cabin door back towards the stern) would that then hold the shape while I then remove and replace the stern beam?
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Family Four restoration advice needed.

Post by dellquay13 »

I did mine in one go, but i didn't go all the way back to the transom, i stopped about 3" in front of the 2 quarter lockers either side of the sump under the outboard well, as the sole from there on was sound.
I used two boards to make the job easier than trying to lay a single sheet, with the join running across the boat, over a batten cut into the foam and resting on top of the gullwing arches. But i guess there is no obviously wrong way.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Family Four restoration advice needed.

Post by dellquay13 »

I've just reread your post with the pictures.
I stopped at about the big beam at the stern of yours, but I don't think mine had such a big beam, I had about 5 smaller beams spaced across the sole. It's likely that over the years Shetland tried all sorts of arrangements, partly depending on what they had to hand for each particular build.
If you are going to use a pillar seat, I'd suggest as much stiffening under the floor as you can manage, as wide as you can. Your weight swaying around on the end of the pillar will be like taking a massive crowbar to the pillar base fixings.
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
KenGreenaway
Posts: 11
Joined: Tue Apr 20, 2021 1:34 pm

Re: Family Four restoration advice needed.

Post by KenGreenaway »

Progress
You do not have the required permissions to view the files attached to this post.
dellquay13
Posts: 556
Joined: Tue Mar 15, 2011 7:45 am
Location: Pequod, F4 mk4, Milford Haven Marina

Re: Family Four restoration advice needed.

Post by dellquay13 »

👍

I've got the same wheel too!
I have now sold my 1989 F4 mk4, 2015 70hp 4str Yamaha. Milford Haven. I proudly owned it for over 20 years, before changing to sailpower and a yacht...
Adam
Posts: 86
Joined: Tue Oct 02, 2018 3:38 pm

Re: Family Four restoration advice needed.

Post by Adam »

dellquay13 wrote: Wed May 12, 2021 4:58 pm 👍

I've got the same wheel too!
Me too :mrgreen:

By the way lads, I'm about to paint my boat inside, just only walls (its called gunnels right?) and bilge (I did cabin a year ago it looks amazing). I thought it might be OK to use bilge paint for that job. ,Or maybe do you have some preferences? What do you think?
Shetland Family Four "Foxy Lady" , 70 hp Johnson EFI four str. You can meet me in the Poole Bay or Lyme Bay area from time to time \m/