Black Hawk refurb - Day 1

Thoughts, Ideas and General Questions
Deaks
Posts: 71
Joined: Sun Dec 02, 2012 6:31 pm
Location: 'Fortune', Black Hawk, Harrogate

Black Hawk refurb - Day 1

Post by Deaks »

I'll be keeping a log of progress on Fortune's refurb. If nothing else it'll remind me how to put it back together!
Forgive me if it all seems a bit obvious.
I've taken tons of photos and will include a few. If anyone has a specific area they'd like photographing please let me know.
Day 1.
Remove rubbing strip.
The strip is held in place with two caps at the stern. One of them, pictured, had two stainless bolts straight through which came out easily. The other had four self tappers which needed drilling out.
Image
Once removed the strip comes off easily. Unsure yet whether to clean up or replace.
Remove two aft cleats.
Dead easy after side panel is removed.
Remove large foredeck cleat.
Not so easy due to extensive corrosion of nuts but doable with patience and penetrating oil. Ratchet for inside cabin and enormous flat-bladed screwdriver for outside.
Image
Remove bow fairleads.
Impossibly corroded nuts within anchor bay. Cut nuts away with small angle grinder and wafer thin cutting blade. Tricky access but OK with a bit of patience.
Image
Anchor hatch.
Dead easy. All bolts came undone after a bit of penetrating oil.
Image
Front grab rail.
A pig to get off. Completely corroded nuts both in the anchor well and in the cabin roof. Resorted to grinding off the nuts in both cases.
Image
Cabin roof handrails.
Also dead easy after penetrating oil.
The cleats and handrail brackets are supposed to be black. Pondering on whether to powder coat or go cheap and cheerful with black smooth Hammerite. I'll decide when I've cleaned up the windscreen surround, which also should be black.
Image
I've also been experimenting with methods of removing the nasty topside paint. Below are the untreated port and chemically stripped starboard rear corners.
Image Image
The stripper, Owatrol Marine Strip, did a great job and left a dead smooth finish. Took 18 hours though in current temperatures (8-10C). It'll be invaluable on the textured topside walkway surfaces where sanding will be impossible. I think using it for the whole topsides, though, would work out expensive. I'll monitor how far twenty quid's worth goes.
A very therapeutic four hour's work. Family dinner tomorrow so no chance to do much - might get up early and sneak an hour or two. Rear rails and light mast look easy.

Deaks
rob
Posts: 92
Joined: Mon Sep 03, 2012 7:13 pm
Location: Northern Ireland

Re: Black Hawk refurb - Day 1

Post by rob »

Great work deaks and great pics, keep it up. How is your anchor hatch held closed...? There is no catch on mine at all...!
Rob.
Deaks
Posts: 71
Joined: Sun Dec 02, 2012 6:31 pm
Location: 'Fortune', Black Hawk, Harrogate

Re: Black Hawk refurb - Day 1

Post by Deaks »

Gravity. If there ever was a locking mechanism it's ferrous oxide by now........
rob
Posts: 92
Joined: Mon Sep 03, 2012 7:13 pm
Location: Northern Ireland

Re: Black Hawk refurb - Day 1

Post by rob »

Deaks wrote:Gravity. If there ever was a locking mechanism it's ferrous oxide by now........
Must all be the same.....!
colinpearce
Posts: 76
Joined: Tue Mar 15, 2011 12:28 pm
Location: Yala, Black Hawk, Honda 90HP, Trailered Anglesey

Re: Black Hawk refurb - Day 1

Post by colinpearce »

Same here, no sign of anything ever been fitted, always stays put so no worries