Help Please
-
stuart50
- Posts: 48
- Joined: Wed Jun 18, 2014 8:20 pm
Help Please
Can anyone shed any light on the year of my Shetland 535
-
IlsonMark
- Posts: 42
- Joined: Thu Oct 02, 2014 12:27 pm
- Location: Ilkeston, Derbyshire
Re: Help Please
There is a list of serial numbers and years is in this thread here. - viewtopic.php?f=14&t=282
Looks like yours is late 60s according to this.
Looks like yours is late 60s according to this.
-
stuart50
- Posts: 48
- Joined: Wed Jun 18, 2014 8:20 pm
Re: Help Please
Many thanks for your quick response, the reasons why I was asking is that I am looking for a secondhand 4 stroke engine up to 20 HP and was asked by by a seller if I wanted long or short shaft.
The guy said if it was an early model it would only be a short shafted engine . Looks as though its a short shaft then
Kind regards
Stuart
The guy said if it was an early model it would only be a short shafted engine . Looks as though its a short shaft then
Kind regards
Stuart
-
DACS
- Posts: 77
- Joined: Sat Jul 19, 2014 9:59 am
Re: Help Please
You would probably be better of measuring the transom rather than estimating whether your boat is an early or late one.
As a general guide outboards can have short, long or extra long shafts which are 15", 20" and 25" long respectively. This measurement is from the underside of the outboard bracket to anti-cavitation plate. Since you want the anti-cavitation plate level with the bottom of the boat you can usually just measure the transom and pick a matching outboard.
As a general guide outboards can have short, long or extra long shafts which are 15", 20" and 25" long respectively. This measurement is from the underside of the outboard bracket to anti-cavitation plate. Since you want the anti-cavitation plate level with the bottom of the boat you can usually just measure the transom and pick a matching outboard.
-
stuart50
- Posts: 48
- Joined: Wed Jun 18, 2014 8:20 pm
Re: Help Please
Sounds like a plan many thanks for your reply
Kind regards
Stuart
Kind regards
Stuart
-
IlsonMark
- Posts: 42
- Joined: Thu Oct 02, 2014 12:27 pm
- Location: Ilkeston, Derbyshire
Re: Help Please
I think it is quite easy to tell with a Shetland 535. For example, here's mine below. This one has a long shaft engine.
viewtopic.php?f=9&t=1818
Now look at the two here. The transom on these is much lower, therefore these are the short shaft model. (At least I assume they are, I've never actually owned a short shaft one!)
viewtopic.php?f=9&t=1173
viewtopic.php?f=9&t=158
Measuring, as mentioned before is also a good idea. But if you look at various pictures of 535s, they all either come with one of these two transoms.
viewtopic.php?f=9&t=1818
Now look at the two here. The transom on these is much lower, therefore these are the short shaft model. (At least I assume they are, I've never actually owned a short shaft one!)
viewtopic.php?f=9&t=1173
viewtopic.php?f=9&t=158
Measuring, as mentioned before is also a good idea. But if you look at various pictures of 535s, they all either come with one of these two transoms.
-
stuart50
- Posts: 48
- Joined: Wed Jun 18, 2014 8:20 pm
Re: Help Please
Many thanks it would appeared mines a long shaft so I will have to measure to confirm once again thanks for the pictures
Kind regards
Stuart
Kind regards
Stuart
-
daveinglasgow
- Posts: 680
- Joined: Tue Mar 15, 2011 9:04 am
- Location: Dave Ashton, Shetland 610 Glasgow & Loch lomond
Re: Help Please
with luck it will be a long shaft as they are far easier to get hold of! 
http://www.ashtonmarineservices.co.uk, Brokergae, Trailers, advice, boat transportation 0759 563 8185
https://www.facebook.com/ashtonmarineservices
https://www.facebook.com/ashtonmarineservices